Quantcast
Jump to content

Arctic Cat 500 4x4 Fuel Problems


Recommended Posts

If You already checked the float. I would make sure the overflow drain on the carb is not blocked. Also clean your air filter, with a blocked filter you can be running rich.

Are you changing the oil? I used some cheap wet clutch safe oil and changed it after every ride while I was trouble shooting. In my case it ended up being a dirty carb.

The other causes could be a suction from the intake created by trailering the quad lifting the float in transport but if you have a fuel pump that will only allow a small amount of gas into the cylinder.

Also be careful not to hydrolock the piston if the excess gas compresses above the piston. If its hard to cranks just pull the plug and blow everything out by turning it over.

Link to comment
Share on other sites

I have taken the carb off twice and completely disassembled/cleaned and put back together, and it is still doing the same thing. Is it possible that my rings or valves (or both) are bad? Its a little hard to crank at first, but runs like a champ.....just scared to run it with all that fuel in the crank case.......thinking I may end up just taking the complete top end off and replacing rings and valves.....just didnt want to if it isnt needed.

Link to comment
Share on other sites

I would do a compression test first.

Another trick is to change the oil and note exactly how much oil you added, then drain the oil into a sealable see thru container and watch the gas float on top of the oil. This way you can measure how much gas is getting by. I did this every time I changed something. When there was no gas seperated on the top I knew I had the problem solved.

Link to comment
Share on other sites

Does smoke come from the exhaust when it runs?

I agree it isn't good to leave gas in the oil. I would change it with some cheap stuff until you find the root of the problem. Because gas seperates from the oil I changed my oil a few times and monitored it. I also let the machine warm up and mix the oil with the gas before I drained it.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
×
×
  • Create New...