Quantcast
Jump to content


2007 arctic cat 700 efi wont run

lamaredskin

By lamaredskin
in Arctic Cat ATV Forum

 Share

Recommended Posts

swampcat07 Grand Master

swampcat07

Posted
Posted

When you put the belt on did you use a bolt from the case to spread the secondary? This will allow the belt to fit on the primary. How about the dry side of the case was there belt dust or debris in there? Did your rollers travel up and down freely? Make sure you use red loctite when reassembling.

Not related but did you change your spark plug? Does the bike have snorkels or an aftermarket exhaust?

Link to comment
Share on other sites
  • 3 weeks later...
  • 4 weeks later...
  • 1 month later...
  • 2 months later...
  • 2 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • luckyyyyesther
      need help choosing UTV soundbar gift plz (~$300 Budget)
      By luckyyyyesther
      Hey all!
      I'm on a mission to buy my first UTV soundbar as a gift for my dad(a newbie on ATV). I'm aiming for something that offers great sound quality without breaking the bank – my budget is around $250. Right now, I'm considering options like ecoxgear, kemimoto, and boss.
      Does anyone have experience with these brands or specific models that you'd recommend? Any advice or suggestions would be super appreciated!



    • Sofaspud
      2008 Can-am Outlander 800 R hard shifting issues
      By Sofaspud
      My 2008 can-am Outlander 800r is having hard shifting issues. Does anyone have a fix for this ?
    • Am2007
      2006 Can-Am Outlander 400 XT Oil presure light is on
      By Am2007
      Hi everyone,
      Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so. 
      I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
      owner manual
      service manual
      engine manual
      I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it.   im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
      Thanks

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...