Quantcast
Jump to content

2002 arctic cat 500 auto won't go forward or reverse

sprad22

By sprad22
in Arctic Cat ATV Forum

 Share

Recommended Posts

DirtDemon Veteran

DirtDemon

Posted
Posted

Agreed, if the belt sheaves are grabbing and moving the belt properly, then the next possible problem is definately the drive clutch. I would tear down to the clutch and check the clutch shoe and the small one way clutch that is between the clutch housing and clutch shoe. Make sure all moving parts are moving freely and check for excessive wear on any clutch components. One question, have you tried putting the machine into 4wd and seeing of the front drive system will move the quad?

Link to comment
Share on other sites
  • 8 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Its-always-something
      98 arctic cat 300 2x4 hi rev choke when started
      By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • kiriyaaoi
      2002 Quadrunner 250- Knackered cam and journal/"bearings", difference between 2001-2002 part and 2000 and earlier
      By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • DarkRider
      Have you ever purchased a quad from an impound auction?
      By DarkRider
      This is something I'm extremely curious about. Has anyone ever attempted to buy a quad (or any other vehicle) from an impound lot? I've always wondered if this could be a bargain, or a waste of time. Google searches do turn up some helpful results. Looks like the state of NJ holds auctions online which I'd be a bit hesitant about.
       
      My online searches haven't really turned up any results of anyone buying an ATV this way. I'd be really curious if anyone tried this, or knows someone who has. I've actually found a couple pages with online auctions for my state, but none had ATVs.
    • alexwv1863
      2016 Arctic Cat 500 Oil Leak
      By alexwv1863
      I have a 2016 Arctic Cat 500 and recently noticed some oil leaking on the engine block to the right of the oil filter. It's near two metal lines going in and out of the engine block. I think one of the lines is called an engine oil line. I have a photo I'm going to try and attach. Any help would be greatly appreciated. I don't want to start tearing into the engine if I don't have to. I think maybe a gasket or something blew around one of these lines. The ATV runs fine otherwise. Doesn't overheat or anything.

    • p5200
      bearing and seal replacement questions for 2005 Scrambler 500
      By p5200
      Hello, what is the best method for installing bearings into their race? I've set one in place and tapped it down until it was metal on metal. Is that sufficient? Surely it's not supposed to go into the race until flush? Also. does the coil spring on the seal go into carrier bearing housing not facing out? Thanks! 🙂 Seal goes in until flush correct?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...