Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

1984 Honda TRX 200 - Sporatic Starting


spill

Recommended Posts

ive had this little bike for a very long time and always worked great, start first pull every time, recently i was driving it and it started running rough when i was almost home, it died as soon as i pulled in the driveway ( no spark ) i fixed that problem ( i have tons of parts ) but it still wouldnt start, a couple days ago i went out and gave it one pull and it took right off, i had to hold the throttle open a bit but it was cold out and i didnt use the choke so i expected to have to do that, i let off the gas and it stalled, i left it sit for about 20 minutes and went back out to try again and it wouldnt start, so i took the carb off and cleaned it pretty good, still wouldnt start, went out yesterday and it started right up, i kept it going for about 10 mins by holding the throttle, its running a little rough but not too bad, i let it stall then tried it again and it started no problem ( about 5 or 6 times in a row) so i walked away thinking just need to tune the carb a bit, tried it last night and today and it wont start again, one thing i did notice is that i dont need to use the decomp valve every time i pull it ( sometimes every time, sometimes i can pull it 20 times before it needs it again) keep in mind the motor is in pretty good shape, it doesnt smoke and when the decomp is doing what its supposed to it will rip the cord out of your hand if you dont use it, anyone have any suggestions?? im about to lose it, im leaning toward a broken valve spring or a bent valve, oh yeah, when you pull the choke on with the breather unhooked, you can see gas shooting out of the back of the carb, any help would be great thanks

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By Bobbywolf
      I am working on a basket case for a friend.  It is a 98 Big Bear (YFM350FWB).  It came with a parts machine which is a 96, which I am coming to find out is VERY different from his machine.
       
      Anyway, first thing is first.  I checked compression, 150psi.  Valves are set correctly, and the engine is in time.  I cleaned the carb, and there was some junk in the passages.  It is a chinese carb, which I figured from the lack of markings or lettering altogether.
       
      The bike runs.  It idles ok, but breaks up badly under acceleration.  Pulling a new spark plug shows it is running lean.  White strap, with no black whatsoever.  So I have the carb adjusted with the mixture screw out way too much (about 5 turns), and the diaphragm needle lifted to the top slot.  It is still not getting enough fuel (or too much air).  It backfires through the carb, and cannot get above idle without carrying on.  The carb boot is in good shape, so it isn't pulling any air there.  I did test this as well by spraying ether around the boot when running, looking for intake leaks.
       
      Anything big I am missing here?  I am starting to believe that this chinese carb is the issue.  This quad came with the original carb, which I would like to rebuild and use, but the mixture screw is totally stuck, and stripped way down in its recess.  
       
      Thanks for any assistance.
    • By p5200
      I'm assuming, it's alright to test the engine after adjusting valves without the rear axle installed? Can someone please verify this? I'm waiting on axle parts and wanting to get that done while waiting. Thanks! 🙂
    • By p5200
      Hello folks, my machine wound up with I think water in the tank etc. It runs but speeds up and slows back down randomly. When not running I don't see gas dripping  from the drain nipple on bottom of float bowl and drain screw is closed tight. With normal idle speed I see no leaking. When the idle speed increases quite a bit on it's own, gas appears to start slowly dripping from float bowl drain nipple? I'm wondering if the carb is flooding and the gas is actually coming from higher up and just appears, to be coming out of nipple but, is actually running down the sides of the nipple? I put a kit in the factory Mikuni carb last year after sitting for a while and I think the gas in the jug I used had drawn moisture. I plan to pull the carb tomorrow and clean everything out. I was just curious if anyone else thinks it's probably something in the carb and is, acutally a flooding problem? Thanks Folks! 🙂
    • By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...