2003 Honda 400 ex spark plugs
-
Similar Forum Topics
-
By Uglyside38
I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷♂️
I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off!
-
By rgeiser
View File 2003 Polaris Ranger 400-500 service manual
2003 Polaris Ranger 400-500 service manual
Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV
-
By Mhatayas
My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark ....
Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself .
He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ?
Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too )
If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
-
By kiriyaaoi
Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves. From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match. I have no idea what this would cost.
2. Buy a replacement head+cam+valve cover.
#1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option. However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number, 11100-19B10, instead of 11100-19B01 like for all earlier models. What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years. Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical. Would those work as well possibly? I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on. Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
-
By Drillbit
Hey all,
I need some input on a problem I'm having with my Kodiak 400 that keeps fouling plugs. First off, I've done a lot of work to this thing, most of it all in good fun. Brake work, cv joints, u joints, carb kit, checked valve lash, compression good, changed all fluids, etc... My problem is it keeps fouling plugs very quickly. I can put a new (manual recommended plug) in and it starts right up, runs great, idles great, picks up good. Doesn't stutter at all. I ride it for 1/2 a mile, it cuts off and won't start back up. I let it sit overnight thinking maybe it got to hot. Try to start it the next day, nothing. Put a new plug in, fires right up, runs great for another 1/2 mile or so, dead. The plugs come out and look carbon fouled with dry black soot on them. I don't know if this is a fuel/air mixture problem or a ignition problem. A couple of things that I noticed is I never need to pull the choke out to start it. Also, when it starts it automatically idles high like an automatic choke would do, then it comes back down to a good idle. Also I noticed that the air/fuel mixture needle valve screw does nothing when I adjust it in or out. I can screw it all the way closed and the motor still runs and idles good. Any advice would be greatly appreciated. I'm almost leaning to a ignition breaking down the plugs??
Thanks!
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.