Quantcast
Jump to content

TRX 400 ex dies when hot...


KrazyRdR83

Recommended Posts

I want to thanks those in advance that help me out with this.

Lately I've been having some running issues with this thing. When I first start it up, runs fine with no issues. I'll ride it for up to 5 minutes, and when nice and hot, idle begins to drop and eventually cuts off.

Carb has been taken off a few times now to make sure things are clean, filter was cleaned, valves were adj as they were a little loose (when adj it actually took a bit longer to die). For some reason I can't get to the sparkplug...? What else, oh, petcock was replaced, and made sure fresh has was used. When I try to restart it will only start if I give it gas, and when I try to let it idle, it idles really low then cuts off.

But once I let it cool down long enough, it will start up (off the choke) every time and idle, take it for another ride, and when up to operating temps or higher issue comes back.

Juan

Link to comment
Share on other sites

I am thinking you have an ignition problem, some ignition components will start to fail when they get warm. Ride it until it dies then pull the plug wire off and check for spark. If there is none, start checking ignition parts, coil, CDI, stator, pickup, plug wire, and all wires and switches in the ignition circuit.

Link to comment
Share on other sites

It's an 05...but got it figured out.

Here's what was going on, after checking things over and over again. Got it running and hot, put the air box back on, and as I went to put the crankcase vent on, it would start to die. Once removed the idle would pick back up. So this whole time, once the motor got up to temp, the crankcase vent hose would pull air away from the carb...

Link to comment
Share on other sites

I'm sorry, I did not mean the air cleaner, there is a second blow by tube on the valvle cover, it may have a filter on it, or it may run into the airbox. Either way, make sure nothing is obstructing it. Also, the lower tube that comes out of the crankcase is connected to a catch tank that attatches to the intake tube, make sure that tank is not clogged either.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By N00bie
      From Arkansas. Just bought a 2012 Gator 850i RSX because I could not pass up the price. BUT it has an idle problem. So, to be honest, I joined just to get a service manual. I have a choice: 1)Buy a hard copy: ~$100; 2)Buy a CD ~$35.00; Get a direct download for free posting 10 times; or get a download for $29.00 (subscription). Haven't decided what to do yet.
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Louznmemind
      Howdy y'all, I'm trying to fix a neighbors 2015 Brute Force 300. Came in with hard to start and won't idle except on choke issue. I pulled the carb and found the pilot jet as well as the emulsion tube partially clogged. Cleaned up everything, put it back together, still having issues...  It will start right up on choke and will also start off choke if you give it just a touch of throttle but it absolutely will not idle unless it's choked just a touch. Also, excuse my ignorance but I'm assuming the "dial" thingy attached to the carb that turns in and out is for setting idle?? 
    • By dhallftworth
      Hi everyone, I received a 98 Yamaha Timberwolf from my brother for free, and I'm working on getting it going. 
      I am having the following problem: 
      The engine is backfiring through the carb. 
      I have done the following to try and get the four wheeler running: 
      Rebuilt the carb and set the air screw to 1-1/4 turn out and the circlip at middle position 3
      Replaced the coil, because the cable was loose at the coil end
      Repaired the main ground, coming from the battery
      Replaced the ignition switch, because my brother couldn't find the key. New switch tested good
      Tested the kill switch and it tested good
      New coil tested goodfor both primary and secondary coils
      Pickup coil resistance is at 195, which is correct
      My source coil, is where I believe the issue is. The resistance is 310ohms, and it should be between 428-523ohms
      When I opened the stator housing, there was significant oil, which I have read is normal. Does it sound like I'm on the right track replacing the source coil? Could this be causing my backfiring issue? It looks like the source coil is part of the stator assembly, is this correct? 4BD-85510-20-00 STATOR ASSY
    • By luckyyyyesther
      Hey all!
      I'm on a mission to buy my first UTV soundbar as a gift for my dad(a newbie on ATV). I'm aiming for something that offers great sound quality without breaking the bank – my budget is around $250. Right now, I'm considering options like ecoxgear, kemimoto, and boss.
      Does anyone have experience with these brands or specific models that you'd recommend? Any advice or suggestions would be super appreciated!



×
×
  • Create New...