Quantcast
Jump to content


04 Honda 250 ex carb issue


mshay

Recommended Posts

ok so im in the army and today was the first time in 3 years that i tried to start my quad.

i put fuel in it and it started to leak from a fuel line at the bottom of the carb. now of course it stopped when i turned the fuel off.

now usually when i was riding it several years ago the only time it would leak would be when doing wheelies or whenever its on the back bumper.

oh also its leaking from that line and not firing, its getting fuel from the main line and its getting spark.

just not sure why the fuel is pooring out and its not firing up.

Link to comment
Share on other sites

Fuel will form gummy and sometimes hardened deposits when it sits for a while. Sounds like whatever fuel was left in your carb, and it doesn't take much. Has done just that. The reason that fuel is leaking out of the carb is because the float is stuck down and not rising to stop the fuel when the bowl gets full as it should. The reason that it won't start is probably because the jets are clogged. What you need to do is take the carb off the bike, take it completely apart and clean EVERYTHING, every nook, cranny, crevice and passage. Torch tip cleaners, carb cleaner, wire brushes and compressed air will be handy.

Good luck, and thank you for your service to our country.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...