Quantcast
Jump to content

300 Bayou missing out half the time


Recommended Posts

2000 Bayou misses out about half the time.

I have done the following

Cleaned the Carburetor.

Replaced the plug and check the plug wire, its wire, Checked the plug boot it ohms out at 500 ohms

Motor has 125# compression.

I did find a barked place on the pickup coil wiring coming out of the motor case.

I pulled the cover and ohm the pickup coil. It ohms at 470 ohms. I repaired the barked insulation and reinstalled.

I replaced the igniter with a new one.

I was told that the voltage regulator could be the problem so I unplugged it and made made sure the battery was fully charged and started it and ran it off the battery only. Still misses out.

I added a jumper wire to ground on the igniter to make sure there was not a bad ground somewhere. I also added a hot wire to the igniter to be assured that the key or kill switch was not the problem.

Nothing I have done has corrected the problem.

Attached is a video. Note: the video camera does not show what the human eye sees. The timing light does not light when it misses but the human eye sees that it is dim during the times the video shows it not flashing.

[ame]https://www.youtube.com/watch?v=QlSE7bIhWI8&list=HL1396568821[/ame]

Any Help any of you guys or gals can give me will be appreciated.

Thanks

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By Gwbarm
      I Ran across this video today comparing an aftermarket to OEM Carb on Suzuki Vinson, thought it might generate some interest, it is quite long but informative.
       
    • By DarkRider
      This is something I'm extremely curious about. Has anyone ever attempted to buy a quad (or any other vehicle) from an impound lot? I've always wondered if this could be a bargain, or a waste of time. Google searches do turn up some helpful results. Looks like the state of NJ holds auctions online which I'd be a bit hesitant about.
       
      My online searches haven't really turned up any results of anyone buying an ATV this way. I'd be really curious if anyone tried this, or knows someone who has. I've actually found a couple pages with online auctions for my state, but none had ATVs.
    • By alexwv1863
      I have a 2016 Arctic Cat 500 and recently noticed some oil leaking on the engine block to the right of the oil filter. It's near two metal lines going in and out of the engine block. I think one of the lines is called an engine oil line. I have a photo I'm going to try and attach. Any help would be greatly appreciated. I don't want to start tearing into the engine if I don't have to. I think maybe a gasket or something blew around one of these lines. The ATV runs fine otherwise. Doesn't overheat or anything.

    • By p5200
      Hello, what is the best method for installing bearings into their race? I've set one in place and tapped it down until it was metal on metal. Is that sufficient? Surely it's not supposed to go into the race until flush? Also. does the coil spring on the seal go into carrier bearing housing not facing out? Thanks! 🙂 Seal goes in until flush correct?
×
×
  • Create New...