Quantcast
Jump to content


08 Prairie 360 start problem

Percherongal

By Percherongal
in Kawasaki ATV Forum

 Share

Recommended Posts

Percherongal Newbie

Percherongal

Posted
Posted

Turn on key, put it in Neutral, lights on steering column light up. NO head lights and the electric start switch will not work. Let is sit for a few hours, started right up. Sat over night and same issue. Checked fuses and they were good. battery is giving 12 volts. Opened up the ignition assembly and it isnt getting any power it comes up as a .01 on the volt meter. Pulled the spark plug to check for spark and NO spark. Will not pull start either. Unhooked the battery checked the spark while trying to pull start it and got a weak spark.

Pushed it into the garage and it sat for 2 days. Turned the key and pushed the start button and it cranked but the spark plug wire was off so plugged the spark plug back in and pushed the start button and nothing. If you jump the solenoid it will crank over but not start. Soo confused , anyone have any ideas?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • mehim
      In search of the backwoods nudist campsites and ready to select the right ATV.
      By mehim
      Hi everyone. 
      Let me explain the thread title. 
      My husband and I are very active in the nudist community, and we have stayed at many and most of the mainstream nudist and clothing optional campgrounds in the USA. We are now approaching our retirement and would like to start a podcast to share those off the road / backwoods / little known camping areas where nudity is allowed. We have purchased a 5th wheel camping trailer with a rear garage for the ATV and now need some good reports on the one to buy. 
      We are most interested in a side by side unit but would love to get your thoughts. 
      Feel free to stop by and say Hi and ask anything you would like to better understand what we are looking for in an offroad unit. 
      Thanks for reading and hope to hear from you. 

    • Its-always-something
      98 arctic cat 300 2x4 hi rev choke when started
      By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • Tuzz
      1990 Suzuki King Quad 300cc Kicks and bucks when accelerating unless ignition switch is in LIGHT position.
      By Tuzz
      Bucking started about a month ago and works ok after 1/2 hour warmup.  Today while working on it i discovered that if i put the ignition switch in LIGHT position it runs fine right from the start.
      I'm stumped!  Any idea why this could be?  

    • BuckBilly
      The Official Good morning thread!
      By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...