Quantcast
Jump to content

Problem for Brut force 750


Recommended Posts

I had to remove the fuse box on my 05 Brute. the 4wd quit working and run through all the steps with actuators and control c.u.e. but it was the wires attached to the fuse box. The metal connectors rotted out and lost connecton. Quick fix is to install fuse links to match existing size and it works great and it cost 22.00 to fix it. save alot of money and time doing this.and it also eliminates future problems associated with water and mud trapped under fuse box.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Louznmemind
      Howdy y'all, I'm trying to fix a neighbors 2015 Brute Force 300. Came in with hard to start and won't idle except on choke issue. I pulled the carb and found the pilot jet as well as the emulsion tube partially clogged. Cleaned up everything, put it back together, still having issues...  It will start right up on choke and will also start off choke if you give it just a touch of throttle but it absolutely will not idle unless it's choked just a touch. Also, excuse my ignorance but I'm assuming the "dial" thingy attached to the carb that turns in and out is for setting idle?? 
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By Suzukiquad
      If you had to choose one mod that you couldn't live without, or had to recommend one what would it be? 
    • By afterburn
      From North Carolina here and glad to join this group.
    • By 2wdrancher
      Hello everyone I have done a ton of research on doing this conversion because I hate getting stuck in the stupidest places and not being able to back out. I will be documenting my conversion here and on a couple other forums and probably post a couple videos on YouTube. So what I’ve come up with is all you need is a front axles, front propeller shaft, the final shaft inside the engine and the 4x4 front engine cover . I will list all the part numbers for everything that you need and prices from about six months ago (sorry) , you DONT need to switch out hubs, knuckles, or anything like that, and if you want differential lock lock like the foreman and Rubicon you can get a foreman Rubicon front differential and propeller shaft with the diff-lock and get a knight sure four manual actuator for it and voilà you have four-wheel-drive rancher. Input from you guys is greatly appreciated thank you for your time!
      Note: I would definitely get the aftermarket HD axles because they are definitely stronger and are around the same price as oem 
      FINAL SHAFT
      23611-HR3-A40  =$80.48
       
      BEARING
      91006-HP5-601   =$11.11
       
      OIL SEAL
      91202-HR0-F01   =$ 7.94
       
      COVER ASSY., FR. CRANKCASE
      11300-HR3-WB0   =$206.99
       
      PROPELLER SH AFT
      40400-HR3-A20   =$91.50
       
      FINAL GEAR
      41400-HR3-W50   =$714.88
       
      FINAL CASE BRA CKET
      50350-HR3-A20  =$7.40
       
      FLANGE BOLT
      95701-08016-08  =$1.49
       
      R. SHAFT SET
      44250-HR3-WB1  =$240.64
       
      L. DRIVESHAFT
      44350-HR3-WB1  =$240.64
      This is all for the 2x4 - 4x4  lever that comes in stock on the ranchers. I would definitely recommend looking for parts for wheelers on marketplace,  or craigslist
       
      001
      NUT, ADJUSTING 
      41560-HP5-600
      $6.51
       
      002
      CABLE, FR. FINAL CLUTCH 
      41570-HR3-A21
      $6.56
       
      003
      SPRING, CLUTCH CABLE 
      41571-HP5-600
      $1.95
       
      004
      CLIP, CLUTCH CABLE 
      41573-HP5-600
      $3.23
       
      005
      GROMMET, CLUTCH CABLE 
      41716-HP5-600
      $3.12
       
      006
      LEVER, FR. FINAL CLUTCH 
      54030-HP5-600
      $8.91
       
      007
      PILLOW BALL, FR. FINAL CLUTCH 
      54031-HP5-601
      $10.87
       
      008
      BRACKET, FR. FINAL CLUTCH 
      54040-HP5-601 
      $11.19
       
      009
      SPRING, FR. FINAL CLUTCH 
      54041-HP5-600
      $1.86
       
      010
      GATE, FR. FINAL CLUTCH 
      54050-HR3-A20
      $4.55
       
      011
      GRIP, FR. FINAL CLUTCH 
      54321-HP5-600
      $8.95
       
      X2 012
      BOLT, FLANGE (6MM) 
      90111-162-000
       
      $2.54 
       
      013
      NUT, SELF-LOCK (6MM) 
      90343-ZE6-000
      $1.70
       
      014
      JOINT B, BRAKE ARM 
      95015-32001
      $0.82
       
      X3 015
      BOLT, FLANGE (6X12) 
      95701-06012-00
      $1.34
       
       
      Or Forman 520 w diff lock
       
      FINAL GEAR
      41400-HR4-A21  =$732.49
       
      PROPELLER SHAFT
      40400-HR4-A20  = $92.54
      And you definitely need the sure four locker for this
×
×
  • Create New...