Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

inserting video in post


Recommended Posts

I have been trying and can't figure out what the trick is. I want to post the video in the post instead of just a link to the video, I have pasted the code that youtube gives you but it doesn't work in the post, it is just shows up as code. What am I doing wrong?

Link to comment
Share on other sites

For you tube it works if you copy the URL code and then pick the icon at the top of the message board that has the mountains and moon. Paste it in there you are set. I can't get the ones from here to work.

You don't even need to use insertimage.gif, just paste the url from the video page. I noticed that also, where QC videos do not embed like that...

The supported sites are in this thread: http://www.quadcrazy.com/atvforum/announcements-support/3152-embed-videos-within-posts-added.html

Link to comment
Share on other sites

  • 4 months later...
  • Admin locked this topic
Guest
This topic is now closed to further replies.
  • Similar Forum Topics

    • By huntindog
      I am in the process of puting it back together after replacing the DPS gearbox.
      The manual I have states that it will need to be flashed by a dealer. Is this still true?
      Also , I have a mystery bolt That I cannot remember where it goes. M6x 70 or so.  Hex head with a flat washer.I will try to attach a pic.
      Pic is no go for now....Cox issue I will try again later
      TIA
    • By Spritee1
      polaris 2008 50 outlaw automatic: got the 50 for free. would only run with chock on, replaced the carburator with new. I can't get the unit to an idle where the machine doesn't move forward. if I do get it to idle down within a few moments it will die. got something to try?
    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By beast6228
      It's been a long time since I have used a forum, I was the admin of one for quite a few years, had thousands of daily active members, with lots of crazy posts and spammers, so I salute the admins. Anyway, just waving my greasy hands, Hopefully I can help others out.
    • By DaDolt
      So, I found myself in the only 5' deep water hole in Moab with the King Quad. Before I could get off it swallowed water at idle and died. The river water was not very clean. I pulled the plug and pumped the water out of it with the starter. I cranked on it and it popped for a second and then was done. Towed it back to the trailer. When I got home I checked the compression and it had none. I have a factory service manual. Disassembled and found the rings stuck in the piston lands. New rings and back together. I try to start it and get a C12 code CKP - crank position sensor. Troubleshoot and find it to be shorted. Installed aftermarket CKP, still get code. Check voltage on new CKP and only get 4.5V, manual calls for 5V minimum. Pulled every connector apart on vehicle and cleaned. Have continuity from CKP sensor side of connector to ECM harness. Install a known good ECM from another 2005 KQ I have. Vehicle fires and I let it run for 10 minutes. Shut it down and put the original ECM in and get a C12 code again and won't fire. Put the known good ECM back in and get C12 and no fire. Tested both ECM's in the other KQ and runs well on both ECM's. Installed a used stator and CKP. Still get a C12 code. Check used stator, 200 ohms and 6.5 V out of the CKP at the ECM harness. Checked ground at ECM harness and it is good. Checked spark with spark plug and without, none. Checked resistance and peak voltage on coil and it is in spec.
      This thing has me baffled. All of the electrical possibilities seem to check out. Might be far fetched, but could the rotor key have sheared when it shut down suddenly when the cylinder filled with water? I know rotary lawn mowers can shear the flywheel key when the blade stops suddenly from a rock or stump. If the key is sheared and the flywheel is out of time by a few degrees could this be giving the C12 code? The voltage output is correct but at the wrong crankshaft position (wrong time).
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...