Quantcast
Jump to content


dune trip


Recommended Posts

how nice for you. i have driven past kill pecker many times but have never stopped to see any of it.

any way ,we are still looking for one more person to make this whole trip possible. if it goes anything like it has in the past , the cost per person for gas should be near $400 each . thats rather cheap to go that far and back . food and your quad gas is your responsibility

Link to comment
Share on other sites

LOL Broke my wrist last year at the dunes !!:laugh:

yep , i have seen a number of guys get hurt at SL .thankfully i have not seen any on get them selves dead,but it does happen. last one i did hear of one rider lost it going over a hill and he got run over by the guy he was riding with.

Link to comment
Share on other sites

ya makes ya think twice about making them jumps when you cant see the other side of the hill.

the last guy i did see get hurt was with several others ,and i think he was the last and tiring to keep up . some how he lost it on what was really flat sand . he went out to the hospital on a board.

at WV HM i saw two different guys lose it. happenedend that they we the last in the line of a number of riders, tiring to keep up with the pack and because of the dust ,they did not know what they had to avoid. ill tell you ,its along way down on some of them trails.

Link to comment
Share on other sites

ya makes ya think twice about making them jumps when you cant see the other side of the hill.

the last guy i did see get hurt was with several others ,and i think he was the last and tiring to keep up . some how he lost it on what was really flat sand . he went out to the hospital on a board.

at WV HM i saw two different guys lose it. happenedend that they we the last in the line of a number of riders, tiring to keep up with the pack and because of the dust ,they did not know what they had to avoid. ill tell you ,its along way down on some of them trails.

yep but it is sure fun to ride sand !! Luck we out west have access to lots of dunes !!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By Suzukiquad
      I just bought two 2002 Suzuki LT80K. Do I need to mix the gas or use straight unleaded?
    • By ResQ91
      Hi guys
      My 87 Bear 350 won't start and could use a hand.
      Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
      battery and connections good
      A Solenoid post jump turns it over
      Neutral Safety Switch wire attached and seems good
      It has not had a wire/switch on Rear Brake Pedal ever since I had it.
      Any thoughts on some other things to troubleshoot this??
×
×
  • Create New...