Quantcast
Jump to content

1989 Suzuki Quadrunner Carb trouble


Dennisg

Recommended Posts

1989 Suzuki Quadrunner.

I got the top end overhauled and putting it back together now.It ran good just smoked.Now it does almost the same thing. Excessive smoking and idling to fast with no adjustment on the screws. I am certain it is a carburetor problem but how to fix it is another problem.

Thanks

dennisg

Link to comment
Share on other sites

I have completed the carb rebuild and the engine runs and smokes just like before with no change except that it runs and starts better. It idles fast and cannot be changed by messing with the 2 screws on the carb. Why does it still smoke and why will it not adjust the idle?

Thanks

dennisg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By Suzukiquad
      I just bought two 2002 Suzuki LT80K. Do I need to mix the gas or use straight unleaded?
    • By jashadams
      Hey all back again with my 1989 moto 4 250.
      After putting a new carb on it it's really sputtery, it has new gas and I'm wondering what to tune on the carb to make it idle better. I've attached a video to describe the issue more. The bike is still work in progress but I think the video gets the point across. Thanks!
      Snapchat-1142015191.mp4
    • By p5200
      Hello folks, my machine wound up with I think water in the tank etc. It runs but speeds up and slows back down randomly. When not running I don't see gas dripping  from the drain nipple on bottom of float bowl and drain screw is closed tight. With normal idle speed I see no leaking. When the idle speed increases quite a bit on it's own, gas appears to start slowly dripping from float bowl drain nipple? I'm wondering if the carb is flooding and the gas is actually coming from higher up and just appears, to be coming out of nipple but, is actually running down the sides of the nipple? I put a kit in the factory Mikuni carb last year after sitting for a while and I think the gas in the jug I used had drawn moisture. I plan to pull the carb tomorrow and clean everything out. I was just curious if anyone else thinks it's probably something in the carb and is, acutally a flooding problem? Thanks Folks! 🙂
×
×
  • Create New...