Quantcast
Jump to content

2006 Suzuki LTZ 400 choke isue???


archer292

Recommended Posts

On a cold start with the choke on full, the bike will start and run but only for a few seconds. Then she dies. I can use the throttle with or without the choke to keep it running but she won't run past a few seconds with the choke on alone. It will stay running after I play with the throttle for a few seconds. Just doesn't seem right. Any ideas???

Link to comment
Share on other sites

On a cold start with the choke on full, the bike will start and run but only for a few seconds. Then she dies. I can use the throttle with or without the choke to keep it running but she won't run past a few seconds with the choke on alone. It will stay running after I play with the throttle for a few seconds. Just doesn't seem right. Any ideas???

What year and have you done any mods to it ?? How does it run when its warm ?

Link to comment
Share on other sites

Runs perfect when it's warm. I have a new old stock yoshimura team suzuki pipe i just put on but it did it with the stock pipe too. Everything else is stock size ( Hot rod crank and bearings, new piston, rings and gaskets all stock size). I bought the bike as a project and what a project it turned out to be. The piston and ring must have just been done because the honing marks were still there in the cylinder. Same thing I was going to do before I checked the conrod small end. I used all new parts anyway. Checked the valves, all good, cleaned the carb. Runs great other than the choke thing and it starts first time all the time so far, I just have to use the throttle.

Link to comment
Share on other sites

Runs perfect when it's warm. I have a new old stock yoshimura team suzuki pipe i just put on but it did it with the stock pipe too. Everything else is stock size ( Hot rod crank and bearings, new piston, rings and gaskets all stock size). I bought the bike as a project and what a project it turned out to be. The piston and ring must have just been done because the honing marks were still there in the cylinder. Same thing I was going to do before I checked the conrod small end. I used all new parts anyway. Checked the valves, all good, cleaned the carb. Runs great other than the choke thing and it starts first time all the time so far, I just have to use the throttle.

What year is it ?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By Charlesbrown
      I’m looking for a top end kit for a Yamaha. I would like to see how well the engine runs before spending $6-$7 hundred on oem. Niche has complete kits from $1-$2 hundred.  Anyone have experience with Niche or similar Chinese companies? 
    • By Sofaspud
      My 2008 can-am Outlander 800r is having hard shifting issues. Does anyone have a fix for this ?
    • By Am2007
      Hi everyone,
      Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so. 
      I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
      owner manual
      service manual
      engine manual
      I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it.   im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
      Thanks
    • By Bobbywolf
      I am working on a basket case for a friend.  It is a 98 Big Bear (YFM350FWB).  It came with a parts machine which is a 96, which I am coming to find out is VERY different from his machine.
       
      Anyway, first thing is first.  I checked compression, 150psi.  Valves are set correctly, and the engine is in time.  I cleaned the carb, and there was some junk in the passages.  It is a chinese carb, which I figured from the lack of markings or lettering altogether.
       
      The bike runs.  It idles ok, but breaks up badly under acceleration.  Pulling a new spark plug shows it is running lean.  White strap, with no black whatsoever.  So I have the carb adjusted with the mixture screw out way too much (about 5 turns), and the diaphragm needle lifted to the top slot.  It is still not getting enough fuel (or too much air).  It backfires through the carb, and cannot get above idle without carrying on.  The carb boot is in good shape, so it isn't pulling any air there.  I did test this as well by spraying ether around the boot when running, looking for intake leaks.
       
      Anything big I am missing here?  I am starting to believe that this chinese carb is the issue.  This quad came with the original carb, which I would like to rebuild and use, but the mixture screw is totally stuck, and stripped way down in its recess.  
       
      Thanks for any assistance.
×
×
  • Create New...