Quantcast
Jump to content


Need Suzuki Info


Dustin83

Recommended Posts

I just got an 2006 Suzuki ltz 400. New to sports bikes I just found the oil tank. I noticed that the oil level was at the bottom hash mark of the dipstick. I wanted to make sure that the oil fill level should be at the top of the hash mark. Please correct me if I am wrong. I didn't get a manual with the quad so Im not sure of the correct oil levels or the amount of oil after an oil change.

Link to comment
Share on other sites

i think you are ok with the bottom hash mark, not alot will go in to top it up i dont think.

this manual should be good for your bike, 2003 thru 2008 ...

just click "to download" and a new page will let you get this manual

https://rapidshare.com/desktop/download/997p1/158558615/MjAwMyBTdXp1a2kgTFRaIDQwMCBTZXJ2aWNlIE1hbnVhbC5yYXI=/49490/0/0/1:25600/6635861DDCD2883DDC15023D93D8D4A8/referer-356939A27F9465EEABDD63953D1B02CC

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By BruceG
      Hi guys. I have a problem where the quad will start and run well for about 5 minutes and then it dies. On inspection the airbox has oil in it (quite a lot). The oil is pumping through the cylinder head breather hose. This problem first happened suddenly. I have since done the top end including, piston, gaskets, rings and valves. I have also done the carb (not that I thought that this was the problem). The compression seems normal. The only thing that I can think of, is that I did not grind the valves well enough. Anyone experienced this? If so, how did you fix it? Any other thoughts?
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
×
×
  • Create New...