Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

2005 Quadrunner Z400 HELP!!!


redshirt

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Gwbarm
      My Yamaha Big Bear shifts through all the gears good, goes into reverse smoothly, but when i go to get out of reverse it takes a lot of effort to get it back to first gear, and even then it does not go very smoothly, have to pull up on the pedal really hard, anyone else ever had this problem. Any ideas would be greatly appreciated.    
    • By drobbie98
      Hey all, Thanks for having me in the forum. I just purchased my first ATV and am stoked to understand more about it. 

      The first stupid question will be, what is everyone's maintenance schedule? DO yo follow the recommended intervals or build one yourself based on the machine. 
       
      Thanks in advance. 
    • By RiverRoad
      I need a wiring diagram pertaining  my polaris 1999 335 sportsman 
    • By pastorjeep
      Hey guys, I just picked up a 09 Big Bar 250 that was completely taken apart. The owner was trying to fix a no spark issue. I put it all back together and sure enough no spark. I have had a Timber wolf, 3 Bear Trackers, and  Bruin 250 over the years so yeah I like these things. After a ohm test on the stator sure enough dead pickup coil, so I ordered a fleabay special. I have put one of these on a couple of the other quads with good results. Anyway, the stator came today and I installed it right away. Quick check and sure enough nice spark. Hook everything up and no start, but a nice backfire through the carb. Clean carb,, no start. Check compression (120psi) no start. Hit it with starting fluid and it back fires real bad, you can hear the starter one way clutch complain. Try pull start and it really jerks your arms. I pulled it back apart and checked flywheel key. Lined up timing marks and they are spot on. Set valves to .004 intake, .005 exhaust. It seems like it is firing on the wrong time. But there is no way to do that, that I can see. Could the new stator pins be backwards? Would it spark but out of time? I am stumped. It doesn't even try to start just bad backfire through the carb. Ideas? 
    • By Params_sweden
      Hi, my KLF300 Bayou 1994 from my other post can now ignite and run for a little while. It's running very rough, the idle is way off, I have to use both choke and gas to get it in a somewhat "idle" state otherwise it dies. Let's fix it
      I think that the first priority is to get the idle stable, right now I can't get it to idle at all, it's either too high or too low and dying off after a few seconds. The setting of the idle screw doesn't seem to stabilize it, it's either too low or too high, if I get it between those states it's only running for a few seconds before dying. The ATV could idle and run last summer btw.
      What do you think I should do next? 
      / Pär
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...