1990 Suzuki LT-F250 2x4 Quadrunner Cutting Out
-
Similar Forum Topics
-
By Uglyside38
I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷♂️
I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off!
-
By hardcastle
My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
-
By Its-always-something
Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
Any help and information greatly appreciated.
-
By kiriyaaoi
Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves. From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match. I have no idea what this would cost.
2. Buy a replacement head+cam+valve cover.
#1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option. However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number, 11100-19B10, instead of 11100-19B01 like for all earlier models. What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years. Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical. Would those work as well possibly? I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on. Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
-
By goodkid_6
I have a 1989 quadrunner LT160. I am looking to replace the plastics. I can't find them for the 89 specifically but I do see plastics for a 91 - 01. Is there a difference in the 89 to the 91 - 01 plastics? From the photos, they appear to be the same with the exception of the holes for the front and rear racks.
Please help clarify if you can. Thanks!
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.