Quantcast
Jump to content


2000 Suzuki King Quad 300 Snorkel Problems


Recommended Posts

Ok I have a 2001 king quad 300 it crapped out about two months ago rite before I put my snorkle kit on. Well I had it all taken appart putting the snorkle on and I decided to go ahead with the kit before fixing the original problem ( yes I know bad idea ) it was running before the kit. It would idle fine but when u reved it up it bogged out and backfired with white smoke common sighns of flooding out so I adjusted the carb after cleaning it 12 hours in soapy water and thorough cleaning on the outside and inside it still ran the same I bought a carb kit and still the same I went back throughout the carb and it was spotless I checked the float and it is fine no spots or anything so I adjusted the fuel to air screw and the needle with no luck I then replaced my fuel pump ( because I noticed fuel running out the back ) still ran the same. I recently had it running for a while putting around in low speed ( ran fine ) give it gas and it boggs out ( too much fuel) I noticed when it boggs out there is air coming out of the snorkle like a blowback I have tried reducing the air intake by covering the snorkle and it has no effect. Im at a los and due to our wonderful economy and my small town job im unable to send it to the shop so im here.

Link to comment
Share on other sites

No but i had planned on checking the spark till i lost all my tools out the back of my truck lol so i have to get more tools .....go figure! Lol thank you for the comment

LOL..that happens to me, I loose tools all the time. They are usually lying somewhere because I forget to put them back where they belong. Then I need something, and it's an hour to find a freakin tool! :laugh:

Link to comment
Share on other sites

Lol well i left my tools at a convenience store as i unloaded a lawnmower, figures with my luck. I have to buy a new battery mine has crashed. It was weird because the starter didnt want to turn it over if the choke was closed or if u gave it any gas during cranking it over it would stop and start clicking. It did that even with the atv battery and a marine battery and a running truck lol. Im yet again stumped

Link to comment
Share on other sites

  • 5 weeks later...

check you petcock. there is a vacuum line that runs from there. the diaphragm breaks and leaks, when you start the motor the vacuum line sucks gas, there it runs very rich. shut off gas, drain the carb. and put vise-grip or clamp on the vacuum hose(close it some how).turn on gas and start it. i am 95% sure this is the problem.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • By N00bie
      From Arkansas. Just bought a 2012 Gator 850i RSX because I could not pass up the price. BUT it has an idle problem. So, to be honest, I joined just to get a service manual. I have a choice: 1)Buy a hard copy: ~$100; 2)Buy a CD ~$35.00; Get a direct download for free posting 10 times; or get a download for $29.00 (subscription). Haven't decided what to do yet.
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By skittle021
      So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer fits - it's far too wide. None of the parts have been replaced, they're all OEM. Exactly the same parts as what I took off a few weeks ago.
      To be more specific, my belt is 1.25in wide, but the gap between the clutch and the primary sheave is only 7/8in wide. I'll include a few photos to explain.
      Has anyone ever experienced such a bizarre problem? Any help at all would be appreciated, I've been stuck on this for a month. I'm open to just about any suggestion.
      Photos: 
       





    • By Louznmemind
      Howdy y'all, I'm trying to fix a neighbors 2015 Brute Force 300. Came in with hard to start and won't idle except on choke issue. I pulled the carb and found the pilot jet as well as the emulsion tube partially clogged. Cleaned up everything, put it back together, still having issues...  It will start right up on choke and will also start off choke if you give it just a touch of throttle but it absolutely will not idle unless it's choked just a touch. Also, excuse my ignorance but I'm assuming the "dial" thingy attached to the carb that turns in and out is for setting idle?? 
×
×
  • Create New...