-
Popular Now
-
-
Similar Forum Topics
-
By Shorty51
Good morning, I am new to the forum. I'm 75 years old and love getting ATVs back to usable condition. I particularly like the 2006-2009 Arctic Cat 250 Utility. I currently own 6. The 2006 I am working on only has reverse and low gear. The "drive shaft" in the transmission is completely stripped where the high gear would mesh. Has anyone on here replaced the shaft. I'm told I have to split the case. I was hoping that someone on here could let me know how hard it will be. I already have it stripped down to where the shaft coming in from the clutch side is the only thing left. I was hoping I could just remove the driven clutch and drive it out from there. Directions say different. Any help would be greatly appreciated.
-
By Yamahahahaha
I'm in the middle of repairing damage from the chain coming off of this from the previous owner. (I learned this is somewhat common on these for various reasons.)
What are you guys using to either help keep the chain correct and on the sprocket or guarding your engine in the case that it comes off / breaks?
Is there an upgraded guard that can bolt around the sprocket in replacement of the currently broken OEM alluminum?
-
By flyinbrian365
View File 2023 Yamaha RMAX4 Wolverine 1000 service manual
Factory service manual
2023 Yamaha RMAX4 Wolverine service manual
Submitter flyinbrian365 Submitted 06/08/2026 Category Yamaha UTV
-
By flyinbrian365
View File 2021-22 Yamaha RMAX4 1000 Wolverine service manual
Factory service manual
2021-22 Yamaha RMAX4 1000 Wolverine service manual
Submitter flyinbrian365 Submitted 06/08/2026 Category Yamaha UTV
-
By hengstserepair
Howdy ya'll. I am working ona 2000 Yamaha Breeze 125. It was in rought shape when I received it and I am working through issues as they pop up. The quad had been sitting for years. I was able to get her running again, but I need your help with the following issue:
I don't trust the transmission yet and I don't want to make problems any worse. So, I haven't pushed things hard at all. Low rpms, less than 5mph in reverse.
Nuetral: Runs as expected
Reverse: She seems to be driving fine at slow speeds. Going into reverse at idle is fine, coming out of reverse back into neutral won't work (the shifter is just stuck). As soon as I turn off the quad, I am able to shift around without any issue.
Forward: It slips. It seems to only transfer power to the wheels on a smooth surface and going slightly downhill. When shifting into forward at idle, there is a clacking sounds during the transition. Shifting back to nuetral works just fine.
Other Notable Symptoms: There was old oil in the vbelt and when I was tuning the carb, it starting blowing out of the CVT cooling vent at the front of the quad. Made quite a mess. There is positive crankcase pressure due to piston blowby, that I have not decided whether or not I am going to fix (customer budget dependant). Since the oil was old, much darker than the new oil that is in the crankcase, I am thinking it seeped past a bad seal while it was sitting for years. The oil that was in it when I first got it had gas in it.
Thoughts: I am thinking maybe there is an issue with the clutch. I worry about the old oil intermingling with the dry centrifugal clutch. I was thinking my next step would be to take the cover off of the clutch and inspect it.
Let me know what you all think. Any advice and ideas is greatly appreciated. This is only the 3rd quad I have worked on and I have a lot to learn.
Lorne
-
COMMUNITY SECTIONS
ATV FORUMS
QUADCRAZY MEMBERSHIP
Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.