Quantcast
Jump to content

Trans slipping in Bobcat 2200 utv

Cliffhnger

By Cliffhnger
in Kawasaki ATV Forum

 Share

Recommended Posts

Cliffhnger Newbie

Cliffhnger

Posted
Posted

We have a Bobcat 2200 (made by Club Car) and the transmission is starting to slip more. It will power out on a hill with loads that used to not be a problem. Is this a sign that the belt is worn and needs to be replaced or could it be something else?

Thanks,

Jere

swampcat07 Grand Master

swampcat07

Posted
Posted

If there is a belt on the UTV sometimes you can just pull the case and check the belt deflection. I am not that familiar with the model but sometimes it can be shimmed. I would also clean the clutch from belt dust with a little brake cleaner. Check that the rollers in the primary also roll freely.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Shorty51
      2006 Arctic Cat Utility transmission drive shaft replacement.
      By Shorty51
      Good morning, I am new to the forum. I'm 75 years old and love getting ATVs back to usable condition. I particularly like the 2006-2009 Arctic Cat 250 Utility. I currently own 6. The 2006 I am working on only has reverse and low gear. The "drive shaft" in the transmission is completely stripped where the high gear would mesh. Has anyone on here replaced the shaft. I'm told I have to split the case. I was hoping that someone on here could let me know how hard it will be. I already have it stripped down to where the shaft coming in from the clutch side is the only thing left. I was hoping I could just remove the driven clutch and drive it out from there. Directions say different. Any help would be greatly appreciated.
    • Jdeaton011989
      Timberwolf 250 starting issue
      By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?
    • Adamb2025
      1990 fourtrax 300 no power no lights
      By Adamb2025
      I have a 1990 Honda fourtrax 300 2x4
      I rode the other day for 30-45 min. Switched it off and now it is completely dead..
      battery is fully charged, fuses are good . WILL NOT TURN OVER ,
      headlights won't turn on , No neutral, reverse or oil temp lights . Electrically it is completely dead !!! I replaced the key switch and CDI box , STILL NOTHING.
      I bypassed the neutral safety switch and grounded it to the battery and still nothing !! I used a jumper wire on the starter Solenoid , the motor will turn over but not start . I even bypassed both fuses and straight wired it to see if I could get a neutral light or headlights still nothing . What could it be ?
    • ButchM
      2023 Hisun Axis 700 fuel problem
      By ButchM
      Hisun 700 EFI. Replaced TMAP sensor had broken off . Fuel pump pressure 41psi. The only way I can keep it running (and runs fine) is to close off fuel return line. 
    • dkgg5755
      2003 Kawasaki bayou 250 carb problem
      By dkgg5755
      This thing came with a cheap aftermarket carb on it the problem I'm having is it won't start with choke installed into carburetor it will start and get run without it installed then bogs out after about 2 min run time I've checked timing , compression, checked valves for proper clearance , also did a smoke test for air leaks found none. 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...