Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

Neri Style Introduces New Big Boy UTV Seat


Recommended Posts

The full base mount design keeps the diver and passenger as low possible to maintain the racer driving position. Big Boy Seat full base in lots of cases prevents the Stock plastic base from breaking. The foam design is the best to lock you in place Big Boy Seat is a direct bolt-on to factory plastic bases.Fit geometry is custom designed for UTV and SUV Vehicles. This is a True Suspension seat,

More...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By Lafytafy
      should i run a thicker oil in a older quad because it make a little more noise than usual 
    • By ResQ91
      Hi guys
      My 87 Bear 350 won't start and could use a hand.
      Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
      battery and connections good
      A Solenoid post jump turns it over
      Neutral Safety Switch wire attached and seems good
      It has not had a wire/switch on Rear Brake Pedal ever since I had it.
      Any thoughts on some other things to troubleshoot this??
    • By Bobbywolf
      I am working on a basket case for a friend.  It is a 98 Big Bear (YFM350FWB).  It came with a parts machine which is a 96, which I am coming to find out is VERY different from his machine.
       
      Anyway, first thing is first.  I checked compression, 150psi.  Valves are set correctly, and the engine is in time.  I cleaned the carb, and there was some junk in the passages.  It is a chinese carb, which I figured from the lack of markings or lettering altogether.
       
      The bike runs.  It idles ok, but breaks up badly under acceleration.  Pulling a new spark plug shows it is running lean.  White strap, with no black whatsoever.  So I have the carb adjusted with the mixture screw out way too much (about 5 turns), and the diaphragm needle lifted to the top slot.  It is still not getting enough fuel (or too much air).  It backfires through the carb, and cannot get above idle without carrying on.  The carb boot is in good shape, so it isn't pulling any air there.  I did test this as well by spraying ether around the boot when running, looking for intake leaks.
       
      Anything big I am missing here?  I am starting to believe that this chinese carb is the issue.  This quad came with the original carb, which I would like to rebuild and use, but the mixture screw is totally stuck, and stripped way down in its recess.  
       
      Thanks for any assistance.
    • By Ajmboy
      So we are almost a month into winter and I've been so busy working on my house that up until today, I didn't realize that we just haven;t gotten any real snow yet to warrant putting the plow on my grizzly. So that got me thinking, what are the latest plows out there and what ATV plows are the best? I've got 2 snow plows for my grizzly, a quadboss pile driver atv plow set up and a snowsport ATV plow. They are both a bit dated now and I tend to stick with the snowsport due to ease of use and I just like it so much. So if you have a plow on your ATV, please let us know what it is and post a picture with your atv/plow would be awesome. Would also like to know what you like and dislike about it.
      This is back a while when I did a write up on these 2 plows.... in 2009 I got the snowsport and in 2012 I got the quadboss.
       
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...