Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By mga
      I have to replace all 4, how much is involved?  Will they slide out of the front yoke? Or, do the boots just slide over the wheel end?
       
    • By prdicon
      Which wheel bearings brand is best?
      Also, I know 2 seals come with each bearings. But there is also a small seal, what is it for?
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By thatoneguy12345
      Hello All, 
       
      Just got my hands on a project ATV. Its a 1999 yamaha big bear 350 2 wheel drive only. I thought I had a manual to diagnose everything, but the numbers are not seeming to match the manual I found online. I have replaced the coils based on the original diagnostics I completed. I can not seem to find an accurate manual for this bike. Anyone help? 
       
      I'm trying to get a wiring diagram that actaully matches the correct wire colors on this bike to assist in diagnostics. 
       
      Thanks! 
    • By DayBreakJim
      So my latest wheeler is a 04 Yamaha Bruin 350. It had all the wires cut from the stator and a few others and no wiring harnesses. The previous owner had them all twisted together and the bike neutral light would come on it would start (hard to start) but then would idle fine. It would die when you gave it gas so I soldered all the wires together and went on inspecting assuming it was a carb issue. Later after the carb was cleaned and adjusted I got this (see video). The bike would want to die anytime you gave it gas and there would be this horrible knocking sound but only when you gave it gas. I was worried it was the rod bearing and electrical still messed up somehow.
      Upon further inspection of the wires coming from the stator there was a W/R wired to R and a R wired to W/R. I switched them so they matched per the service manual (W/R to W/R and R to R) and the bike started right up, idled and revved out fine and the knocking noise disappeared. This was the problem the whole time. It was just really hard to tell bc the oem wires coming from the stator were so brown and dirty I could barely make out which was which.
      Where the hell did that knocking noise go? and what was causing it?? Just racking my brain trying to figure out what it was so I know for next time but I can't make sense of it... Really thought it was the rod bearing but it didn't make the noise at idle so I was questioning it...Luckily I kept searching!!

      20230725_171507.mp4    
       
       
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...