Quantcast
Jump to content

1994 Yamaha Warrior Starting Problems

Vulcan245

By Vulcan245
in Yamaha ATV Forum

 Share

Recommended Posts

Vulcan245 Newbie

Vulcan245

Posted
Posted

Ok i have a 1994 yamaha warrior, i just got it bored 20 over, got the wisco piston to match ok. so i got and put the top end back together and it wount start, it will backfire somtimes but thats it.

I checked for spark... good check for gas...good check for compression.......maybe 20psi

WTF i just had it bored and a new piston and rings. now if i put a cap full of oil in the cyclinder and crank it, it has tone of compression. i have the piston installed right (arrow pointing to the exaust) ajusted the valves checked the timing i even tryed retarding and advancing the timing but in the end i get nothing... can someone plz help me im trying to get it up and running for rumble on the ridge..

Link to comment
Share on other sites
marioweldinginc Veteran

marioweldinginc

Posted
Posted (edited)

You might have the rings in the wrong order or not clocked correctly. Im not sure what your total ring count is but if adding oil raises compression significatly its a problem with the rings or cylinder wall. Timing or valves has nothing to do with it.

Were you able to seat/cycle in the new rings? Until they mate together your compression will be on the low side. Id hate to say iy but i would tear down the motor and check your rings and position. Maybe you put one of the rings upside down

Sent from my SGH-T959V using Tapatalk

Edited by marioweldinginc
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Uglyside38
      1988 Suzuki Quadrunner 250 intermittent spark
      By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

    • Mhatayas
      Baja 250, No Spark , I'm stumped ...
      By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • Drillbit
      1997 Yamaha Kodiak 400 fouling plugs
      By Drillbit
      Hey all,
      I need some input on a problem I'm having with my Kodiak 400 that keeps fouling plugs. First off, I've done a lot of work to this thing, most of it all in good fun. Brake work, cv joints, u joints, carb kit, checked valve lash, compression good, changed all fluids, etc... My problem is it keeps fouling plugs very quickly. I can put a new (manual recommended plug) in and it starts right up, runs great, idles great, picks up good. Doesn't stutter at all. I ride it for 1/2 a mile, it cuts off and won't start back up. I let it sit overnight thinking maybe it got to hot. Try to start it the next day, nothing. Put a new plug in, fires right up, runs great for another 1/2 mile or so, dead. The plugs come out and look carbon fouled with dry black soot on them. I don't know if this is a fuel/air mixture problem or a ignition problem. A couple of things that I noticed is I never need to pull the choke out to start it. Also, when it starts it automatically idles high like an automatic choke would do, then it comes back down to a good idle. Also I noticed that the air/fuel mixture needle valve screw does nothing when I adjust it in or out. I can screw it all the way closed and the motor still runs and idles good. Any advice would be greatly appreciated. I'm almost leaning to a ignition breaking down the plugs??
      Thanks! 
    • McG75
      1996 Yamaha Timberwolf 4x4 Struts and Shocks
      By McG75
      Hello I’m new here and was wondering is anyone knew of good replacement part numbers for front struts and rear shocks for this atv? I think I’ve found a new rear shock, that looks like the original but there is no dimensions or anything and was wondering if there are any afterMarket new front struts available. I know it’s a long shot but any help would be appreciated. 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...