Quantcast
Jump to content


1994 yamaha timberwolf wont start


Bigal700

Recommended Posts

I got a 1994 yamaha timberwolf that 2 years ago i bought put carb on off a parts one had it running but not the best so i rebuilt the carb seemed to run good then i left it sit i wanted to ride it so,i took carb apart to clean it looked good had it running but wouldn't idle not a big deal then it died so i gave up on now trying to start wont do anything i checked spark looks good, has great compression and its getting gas i sprayed starter fluid in it and it still wont do anything what the heck could be wrong?

Link to comment
Share on other sites

the stator makes the spark, it is inside the cover by your left foot sitting on the bike, it is an easy fix, the spark being white is weak, if changed it will be blue. stator and pick up coil are sold together, both inside the cover, you might be able to buy just the pick up coil and try that, sometimes that is all that goes on them ...

Link to comment
Share on other sites

I looked i can get one from any where for the same price i got two more timberwolfs the same year the one i ran it to the ground it ran but cam chain stretched and i never had to replace stator and the other one looked like a new machine when i got it iv had great luck with that one

Edited by Bigal700
Link to comment
Share on other sites

Ok i pulled stator out of parts machine and i pulled carb from one i have that runs good but as soon as it gets warm it dies i thought maybe something wrong with carb when i pulled it so i took it off myn and put it back on running one and that one ran great so there's something still wrong with myn wat could it be?

Link to comment
Share on other sites

Ok now i pulled stator out of my junk wheeler that run but cam chain stretched on and i pull carb off of my running timberwolf and it idles and revs up but once it gets warm it dies and wont start again what could this be? Its not carb pulled it back off myn put it on running wheeler and it runs great so something is still wrong with myn

Link to comment
Share on other sites

  • 4 weeks later...
  • 5 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By McG75
      Hello I’m new here and was wondering is anyone knew of good replacement part numbers for front struts and rear shocks for this atv? I think I’ve found a new rear shock, that looks like the original but there is no dimensions or anything and was wondering if there are any afterMarket new front struts available. I know it’s a long shot but any help would be appreciated. 
    • By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Charlesbrown
      I’m looking for a top end kit for a Yamaha. I would like to see how well the engine runs before spending $6-$7 hundred on oem. Niche has complete kits from $1-$2 hundred.  Anyone have experience with Niche or similar Chinese companies? 
    • By Drillbit
      Hey all,
      I need some input on a problem I'm having with my Kodiak 400 that keeps fouling plugs. First off, I've done a lot of work to this thing, most of it all in good fun. Brake work, cv joints, u joints, carb kit, checked valve lash, compression good, changed all fluids, etc... My problem is it keeps fouling plugs very quickly. I can put a new (manual recommended plug) in and it starts right up, runs great, idles great, picks up good. Doesn't stutter at all. I ride it for 1/2 a mile, it cuts off and won't start back up. I let it sit overnight thinking maybe it got to hot. Try to start it the next day, nothing. Put a new plug in, fires right up, runs great for another 1/2 mile or so, dead. The plugs come out and look carbon fouled with dry black soot on them. I don't know if this is a fuel/air mixture problem or a ignition problem. A couple of things that I noticed is I never need to pull the choke out to start it. Also, when it starts it automatically idles high like an automatic choke would do, then it comes back down to a good idle. Also I noticed that the air/fuel mixture needle valve screw does nothing when I adjust it in or out. I can screw it all the way closed and the motor still runs and idles good. Any advice would be greatly appreciated. I'm almost leaning to a ignition breaking down the plugs??
      Thanks! 
×
×
  • Create New...