Quantcast
Jump to content

1998 Big Bear Carb replacement


crankin

Recommended Posts

  • 1 month later...

the 97-98 4x4 is special in its own little way , now why that is i have yet to figure out other than they only used it on four wheel drive models, i havent heard of retrofitting to a different style becasue it has the boots on both sides instead of a bolt on but you can find aftermarket replacements on amazon for about 170 i will be getting one next week and will let you know how it works for me

Link to comment
Share on other sites

toyotatrukin,

Hopefully you will see this before buying your carb. I found one at zoomzoomparts.com through amazon and it was only around $140. It was delivered in about three days. Perfect fit and this quad never ran so good! I got the quad used and not running so good. I had to use low range to go anywhere. Now I don't even use low range. :yes::biggrin:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Charlesbrown
      I’m looking for a top end kit for a Yamaha. I would like to see how well the engine runs before spending $6-$7 hundred on oem. Niche has complete kits from $1-$2 hundred.  Anyone have experience with Niche or similar Chinese companies? 
    • By jashadams
      Hey all back again with my 1989 moto 4 250.
      After putting a new carb on it it's really sputtery, it has new gas and I'm wondering what to tune on the carb to make it idle better. I've attached a video to describe the issue more. The bike is still work in progress but I think the video gets the point across. Thanks!
      Snapchat-1142015191.mp4
    • By opnea
      Where do yall ride at in South Florida other than the MX track on Krome Ave?
×
×
  • Create New...