Quantcast
Jump to content


yahama big bear 300 gas mixing with engine oil

duckhunterdave30

By duckhunterdave30
in Yamaha ATV Forum

 Share

Recommended Posts

SunLrider Mentor

SunLrider

Posted
Posted
If the fuel is gravity feed, the carb may appear to have a good needle and seat, yet it may not be closing fully. It's also possible the needle and or seat are damage or blocked do to debris in the carbs fuel bowl.

Also,,,,Be sure to turn you fuel off every time you shut your bike down......Also check your Float....

i would go with the carb not closing fully

Link to comment
Share on other sites
  • 2 weeks later...
  • 3 weeks later...
mywifeknowseverythin Grand Master

mywifeknowseverythin

Posted
Posted
If the fuel is gravity feed, the carb may appear to have a good needle and seat, yet it may not be closing fully. It's also possible the needle and or seat are damage or blocked do to debris in the carbs fuel bowl.

Also,,,,Be sure to turn you fuel off every time you shut your bike down......Also check your Float....

Glad I could help:laugh:

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • HSTAR
      1997 Yamaha big bear 350 Shift shaft issue
      By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • BruceG
      2005 Bruin 350cc Oil pumping into airbox
      By BruceG
      Hi guys. I have a problem where the quad will start and run well for about 5 minutes and then it dies. On inspection the airbox has oil in it (quite a lot). The oil is pumping through the cylinder head breather hose. This problem first happened suddenly. I have since done the top end including, piston, gaskets, rings and valves. I have also done the carb (not that I thought that this was the problem). The compression seems normal. The only thing that I can think of, is that I did not grind the valves well enough. Anyone experienced this? If so, how did you fix it? Any other thoughts?
    • John Sinclair
      1992 yamaha big bear 350 carburator issues
      By John Sinclair
      I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY.  ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996.  WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE  CABLES THE NEW CARB ONLY HAD ONE CABLE.  HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE?  
    • Clydaho
      2022 Hisun Sector 550 Gas gauge stopped working
      By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • Mhatayas
      Oil leak 1985 suzuki 250
      By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...