Search the Community
Showing results for tags 'warrior'.
-
I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
-
My 98 grizzly needs a cdi and I refuse to pay $200 for a used one. Will the cdi unit for CDI Box For Yamaha Kodiak 400 YFM400 2001 2002 Warrior 350 YFM350X 1997-2001 work on a 98 grizzly ? Any ideas
-
-
View File Yamaha Warrior 350 Service Manual Service manual pdf Submitter Rick Shropshire Submitted 10/23/2021 Category Yamaha ATV
-
Hello Folks....new to the forum. I have two Warriors (87 and 92), and an 89 Big Bear. Looking for some help with engine issues on the warrior, and my 89 Big bear backfired and died. Got spark, got gas, seems to have compression, (but haven't tested it yet...next). She rolls over good, maybe too good...seems soft. Have spark and enough compression to blow gas mist out the plug hole when cranking. Suggestions, Been running great since we got it.
-
Hello everyone, I am new hope am welcomed. Metu
-
So I dug my warrior out of storage replaced the carburetor with one off Amazon & it was running great. Last week it didn't want to start it would crank & I could smell gas but nothing. I replaced the starter,stator,solenoid,spark plug & coil & resistor but still not starting. Checked the stator and its at 30 ohms tried using starter fluid but nothing. I am completely lost and could use some help thank you
-
1997 Yamaha 350 Warrior, should there be oil in the stator area? Have a no spark situation.
-
my buddys 02? warrior cuts out as soon as you give it throttle. it stays running, but it missfires and pops through the exhaust. it returns to idle and idles fine. the timing looks ok and we have swapped the carb with no change.its been sitting a while waiting on carrier rebuild, it ran fine before that. any ideas?
-
I have replaced the cdi box,spark plug,coil and stator but still no spark.
-
suspension 1990 Yamaha Warrior 350 rear suspension sitting low
Brenden posted a topic in Yamaha ATV Forum
Hi, I just bought a used 1990 warrior and the rear is sagging low like it has a lowering kit but I’m not sure, does anyone know what it could be? -
I have a 02 Warrior i am trying to build a wiring harness i have looked in the manual and i am confused... the pick up has 2 wires. W/R W/G The source rotation coil has 2 wires. One is Red other is white/blue. The manual shows the the white and blue wire connected to the w/g right after the stator... so why is these 2 wires connected? Does not show w/b wire at cdi i have looked at many options with no luck if someone has a 2002-2004 warrior and can take a pic of the wires and location at cdi i would really appreciate it. Thanks
-
I have a Yamaha 350 in at once to try to fire up but won't. It's getting gas fire air and it has a lot of compression but still struggles to start check the timing it's top dead center valves are good valves are adjusted everything's working but won't fire I put my hand over the carb suck in gas and it tries to but it makes a lot of black smoke. Also when I put my hand over do you carb and tried to start it there's black black nasty stuff in the gas. So I don't know if it's trying to burn too much or what it is the gas tank clean and it anything to do with the gas it's with it firing. Took the spark plug out and it's pure black. What is dried up black not nasty corroded wet looking. Need help to solve the issue
-
I have a 2001 yamaha warrior YFM350x and started to work on it. The person who I got it from put a new top end kit in it. I already took the top end off and checked, brand new still. Had to clean the valves so it can get better compression. Put it back together and turned it over and and made good compression but also had a loud clanking noise at the bottom, put hand over carb and stopped making the noise when I turned it over. And won't start. I know it is not the top end. Just cleaned it and valves. Need help trying to figure out what's the problem.. thinking it's the crank rod but don't know. If it is the rod can i just get a new rod for it?(would be great if so). Or does it need a hole bottom end . In need of help.
-
Hello all, I’m working on my sons 99 Yamaha Warrior 350. When I pulled the plastic cover off left side of engine, I can see oil leak at the seal. I pulled the bolt out and then the starter boss(I guess that’s what it’s called?) I can see that the boss doesn’t make contact with the seal. Is there a spacer of some type that slides on to the boss, to make contact with the seal? This seal is held in place with a plate with 3 screws in it. This boss slides into the bearing in the stator. I have been to parts websites and I don’t see what I’m needing. Maybe it’s just the wrong seal?
-
Pull in clutch lever shift into gear and nothing happens ... But When I pull in the clutch lever I hear a clicking sound ... never heard this before ...
-
Used ATV parts available from Resurgence Small Engine Inc. All parts have been identified by manufacturer's part number, photographed, and listed on our website. Our used OEM parts are available for up to 60% off dealership prices. This way you can maintain your machine with well-made OEM parts at a more affordable price! Compatibility can be confusing, but we’ve simplified it for you. Browse our current parts inventory by type, make, year, & model or search by OEM part number. We make the logistics easy with our Free Shipping Promotion on US orders over $100! Visit our website to view our current inventory: https://resurgencesmallengine.com/parts/ Parts are located at Resurgence Small Engine Inc. in Wasilla, AK. Free local pick-up is available and our website is configured for domestic US shipping. For international orders, please contact us. More parts & models to be listed continuously! As of August 2018, parts are available for the following ATV models: Parts are listed for many models, currently including: Kawasaki 2003 KFX400 Polaris 2010 Ranger 500 4x4 HO EFI Suzuki Quadrunner 250 LT4WD 250 LTF250 500 LTF500F King Quad 250 LTF4WDX 300 LTF4WDX 450 Quadmaster 500 LTA500F 4x4 Eiger 400 2x4 400 4x4 Ozark 250 LT250 Vinson 500 LTA50F Yamaha Banshee 350 Big Bear 350 Raptor 350 Warrior 350 Wolverine 350 More parts & models will be added continuously! Resurgence Small Engine Inc.
-
Trying to help a friend with his 2004 Yamaha warrior 350... It wasn’t getting a spark so we replaced the spark plug, cdi box and coil. Have tested the kill switch, checked fuse, everything is good there. Monday (8-20-18) we installed a new stator and got spark, ran it around my trails for about half hour then put it up. Today (8-25-18) we went to go riding and it wouldn’t start, again getting no spark... can’t wrap our heads around what happened when we got spark back then a few days later nothing... any help would be greatly appreciated
-
I got a 02 warrior that seem to fire perfect if pushed backwards but if you push it forwards it sounds like your pushing over the start and it won’t fire going forward but will backwards any help please
-
DC04C4C7-1DDB-48AD-B70A-A024643AF725.jpeg
Gerardo Rodriguez posted a gallery image in Show Off Your ATV
-
-