Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ATV Racing & ATV Events

Do you have an event or promotion you would like to share with everyone, post it here. ATV Racing events, jamborees, etc.

Subforums

  1. Post an ATV Event   (885 visits to this link)

    Post an atv event in the Main Community Events Section. Below you can post it in just the forums.

399 topics in this forum

  1. EVENTS SECTION - Add an ATV Event!

    • 7 replies
    • 7,344 views
    • 0 replies
    • 823 views
    • 0 replies
    • 223 views
    • 0 replies
    • 161 views
    • 0 replies
    • 211 views
    • 0 replies
    • 258 views
    • 0 replies
    • 239 views
    • 0 replies
    • 280 views
    • 0 replies
    • 304 views
    • 2 replies
    • 310 views
    • 0 replies
    • 229 views
    • 0 replies
    • 369 views
    • 0 replies
    • 580 views
    • 3 replies
    • 818 views
    • 1 reply
    • 761 views
    • 2 replies
    • 1,528 views
    • 0 replies
    • 641 views
    • 0 replies
    • 576 views
    • 2 replies
    • 1,246 views
    • 0 replies
    • 582 views
    • 0 replies
    • 889 views
    • 0 replies
    • 572 views
    • 0 replies
    • 770 views
    • 0 replies
    • 815 views
    • 0 replies
    • 839 views
    • 0 replies
    • 688 views
    • 0 replies
    • 944 views
    • 0 replies
    • 628 views
    • 0 replies
    • 960 views
    • 0 replies
    • 654 views
    • 0 replies
    • 896 views
    • 0 replies
    • 690 views
  2. Apex Race Quads

    • 1 reply
    • 970 views
    • 0 replies
    • 1,266 views
    • 0 replies
    • 807 views
    • 1 reply
    • 1,034 views
    • 0 replies
    • 672 views
    • 0 replies
    • 805 views
    • 0 replies
    • 892 views
    • 0 replies
    • 838 views
    • 0 replies
    • 963 views
    • 0 replies
    • 881 views
    • 0 replies
    • 801 views
  3. ORV FUN FEST 2017

    • 1 reply
    • 1,046 views
    • 0 replies
    • 907 views
    • 0 replies
    • 823 views
    • 0 replies
    • 949 views
    • 0 replies
    • 893 views
    • 0 replies
    • 937 views
    • 0 replies
    • 823 views


  • Latest Forum Posts

    • Something to bear in mind: if the adjustment screw is on the engine side of the carb (like this one) it is a fuel screw, so turning it out richens the mixture. Most 4 stroke carbs are this way. If it's on the airbox side, it is an air screw - common on 2 strokes. This works opposite but really does the same thing. It just fine tunes the pilot (slow jet) circuit in all cases.
    • What I would do is take a stainless steel corner square and place it down on a flat surface. Then put the ring in the corner of the square and check for the slope against the edges of the square and then flip the ring over and check again.    
    • Yes I looked at the rings very closely, no marks.  The mark on the original is very easy to see.  No writing, no dots, stamps, paint etc.  Just plain black.  I'll check for taper with a straight edge, thanks for the tip!    
    • If the dark spots are just grease from your fingers then yes the cylinder is fine.   The ring should be tapered and not noticeable to the eye without really looking at it or putting  it up agains a flat surface like a smooth piece of steel or on a metal ruler but its tough to see.  Did you look on the flat spot of the rings, the rings are usually marked there?  
    • The dark spots are just grease/dirt from my fingers, I got the new piston and rings but I'm perplexed.  There are no markings on the rings.  The originals only have a mark on the second ring down, and it's supposed to have a taper according to the manual.  The new rings have no marks whatsoever.  I'm sure the oil rings don't matter but the compression ring should.  I can't see the taper with my naked eye.  The old one doesn't appear to have a taper either but it may just be worn down enough to not see it anymore.  Anyway, if the ring has no marks does that mean it can go in either way?  The instructions are generic but they do state that that the marks go up (assuming there is a mark).   Thanks

×
×
  • Create New...