Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

clsharky

Help with starter relay connector info

Recommended Posts

Hi. The starter relay has burned out on my daughters 1998 LT80 ATV. Im pretty sure the relay is bad, because if I jumper the 12v constant and the 12v switched to the starter at the relay connector, the starter will turn over. I have already ordered a new relay and a brush kit for the OEM starter I have in a box (it has a Chinese made starter installed now, and I dont know what condition it is in, other than it turns when I apply 12v as explained above).

The relay will not be here until next week, and what I want to do is wire in a regular automotive 30 amp relay until the new one gets here. I will leave the connector intact and I have already made 4 male-female jumper wires. What I need to know is which wire goes where on the 5 pin relay, seeing as how the old one is not marked. Typically, the constant 12v goes to terminal 30, the push-button start wire should go to 86, the output starter wire goes to 87 and I am left with one more wire, which is the white/black tracer from the engine stop switch. I dont know where to connect this, and I also dont know if I need to hook up a ground to terminal 85.

Any help with this would be ideal. I am pretty good with wiring, but its been awhile since Ive played around with relays, and I would rather have some advice before continuing. Also, the optional pull starter is not installed on her ATV, and if anyone knows where I could find one, new or used, reasonably priced, that would be nice too. Preferrably in Canada. Thanks.

Edited by clsharky

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By 1911Neil
      I had a quad fall in my lap a couple weeks ago. The only things I knew about it was it was a Kawasaki Bayou 220, was in pretty rough shape and was free. I couldn't say no to a fun little project. I've been looking a different ATV forums gathering quite a bit of info and decided this was the one I wanted to join.
      Thanks to this forum, I found the VIN under about an inch of mud and cross referenced it to be a '98. It had been sitting outside for at least 5 years and was told it ran when parked, but had no brakes. Squirrels or mice had been chewing on the handlebar controls and it's generally just kind of beat up.
      So far, I've gone through the carb (not near as bad as I expected), freed up the brakes (will probably need new cables), replaced the spark plug, air filter, petcock and put a new battery in it.
      The gas tank had been empty and looked clean so I put some fresh gas in it and tried to crank it today. I got a neutral light, but the starter button did nothing. I tried pull-starting it and it wouldn't fire. I checked the plug and wasn't getting a spark. I started digging and found some potential issues and some definite problems.
      I have a wiring diagram I found on here but it's just a picture or scan out of a book and hard to read. I don't see a reference to a black/yellow wire, which is my first problem.
      First, it that a factory crimp? One of those wired looks like it goes to the connector in the 2nd pic. Is that just a spade lug type connector? I pulled on it with some needle nose pliers but it didn't seem to want to come off. In the 3rd pic, should there be a fourth wire?
      I've read through and bookmarked the threads Andrew Baker and Arizona have going but I figured I needed to start with these obvious issues first. I have lots of pictures, so if there is something else you want to see, just ask. If I don't already have a pic, I'll take one.
       



    • By Ed Zeppeli
      Hi,
      Oddly I'm having  a hard time ordering front brake shoes for my '98. 
      I'd appreciate recommendations on decent, widely available shoes if possible. Ideally available in Canada on short notice.
       
      Thanks much,
       
      Warren
    • By Ajmboy
      Disconnected the plow yesterday on my 2004 Yamaha Grizzly 660 and am getting ready to do some riding yesterday and the battery went weak, Starter cranked a few times but week. Put my trickle charger on that I bought and went to the garage today to start it up, but the starter is just spinning and not engaging. The solenoid is clicking. The pull start sucks and is hard to pull (never use it and need to look into that). Quick video of the starter spinning. Could it be the starter or  the starter clutch one-way bearing? I guess I need to take the cover off to see what's going on.

      2004 Yamaha Grizzly 660 Starter Spinning.mp4
    • By Trent Finnessey
      Hey, so I’ve got a 98’ 300ex with a few mods.... jet kit, k&n air filter, it’s got 18” rear tires. I’m just wondering what would be the best mods so I can keep up with say a 400ex on the straight always, I already can in the trails simply because I’m a better rider..... 
  • Similar Tagged Content

    • By Snowden
      Hi everyone,
      I have a question, if the starter clutch gear looks fine but is still not working correctly then all I should need to replace is the one way bearing, right?
      thanks,
    • By Blue
      Hey all I have a question on my 94 fourtrax 4x4. The electric start won't work. When I hit the button I hear the solenoid clicking but nothing happening. I put on a new solenoid and same thing happened. So I took off starter and checked it, brushes looked good nothing looked out of the ordinary. My battery is putting out 11.2 volts. I wouldn't think that would be it since I put a newer battery in from my other quad and still got same results. Any ideas I'm scratching my head on this one.
    • By stepadery
      The connector that that plugs into the switch evidently was caught by something while riding (I'm guessing) and a couple of wires were pulled out of the connector. I have attached a picture. Is there any where that I can get this female end with pigtails without buying the entire wiring harness? I'm a pretty good wire splicer and solderer.


    • By Pure_Michigan
      I bought this old three wheeler that I found in a barn. It looked pretty rough, but I have it running now and functioning.
      With the switch set to "run" and the key in the "on" position the electric starter does not work when I push the starter button,
      However, if I cross the solenoid it will work and it will start the engine - so I know the starter motor is good and it works.
      Now, it gets a little mysterious. When the engine is running, AND the headlight is on high beam, the electric starter will engage when the starter button is pushed.....When its already running! (when the headlight is off or on "low" the starter button does nothing, only when running and in high beam will you hear the starter motor zing when you push the starter button) So, I know the button actually works, but only after the engine is already running and the high beam is on!
      So to recap: with the key on, the starter button does nothing. crossing the solenoid will make the starter work, and after the engine is running the starter will work with the button!
      Has anyone else had this problem? Can anyone point me in the right direction on solving this one?
      Thanks!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...