Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

copedaddy

Sportsman 90 bogging down

Recommended Posts

Have a 2000 Sportsman 90 I picked up for my youngest son. It had been sitting and would not start, so I pulled and cleaned the carb, cleaned the tank, put fresh gas in it and it fired right up. It seems to run out good, but after riding it for a few minutes when you de-cellerate it bogs down and will slowly stall out or drop down to a low idle.

I can fire it back up and it will pick up ok, but every few minutes it seems to want to bog down and throttle response is non-existant. Fuel and plug are fresh.

It does seem to be pretty smoky with the auto oil injection. Could to much oil cause this type of behavior ? Anything else to check?

Thanks

Share this post


Link to post
Share on other sites


Check your gas tank vent, might be plugged. Does it suck in air when you loosen the gas tank cap after it stalls out? Just a thought.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Steven Urban
      First time using this forum.  Owned a Kawasaki dirt bike once, had no issues.  But I picked up this 4 wheeler at an auction.  They stated it ran, but only needed a battery.  Well I do not believe that was all true.

      Some pictures are attached.  Not sure why, but the whole air filter stuff was removed.  They had some small thing inserted as a make shift air filter.

      I purchased a battery to try this all out.  Waiting to return it and get the proper size, as it was too big for the battery box.  But here is my issue I had while the battery was connected.

      1 - The lights on the steering column did not come on.  Not sure if they work or not.

      2 - The starter solenoid seems to be bad.  I have a new one on order. 

      3 - In the pick, there is another rusted part.  Not sure what that part is or what it is used for.

      4 - What is the 12v rectifier?  square bodied part.

      So when I hooked the battery up.  Pushing the start button did nothing.  Pulling the cord to try and pull start, it turned, but would never fire.  I have put in a new spark plug as well, it looked worn out.  With electric start, I crossed over the posts on the start solenoid, it turned over, but would never fire and start.

      I have read a few other threads and it stated something about needed the neutral light on.  SOmething about a kill switch.

      Any help would be appreciated.



    • By bren7176
      Doeas any have the actual electrical diagram for the distirbution block  for this atv > I had a few wire not worky worky so needed to replace ends plus dam thiing is dirty so needs to clean all the contacts ..
      Want to make shure I get eveything back in right place .... I have the repair manual but as we know it no help really .....
       
      Brendan
    • By jimsvtx
      I'm working on my brothers' 2002 Suzuki Vinson 500 . It sat for a few years before I got into it. I'm concentrating on the carb - I replaced orings, needle, etc. and soaked jets, bowl and anything that I could get off the carb that the solution wouldn't eat. I also removed the tank and flushed it with hot water - it's clean. The gas cap innards rusted away and the tank had a lot of rust and water in it before I cleaned it. I replaced the gas cap and installed a new fuel valve because the screens were broken in the old one. The bike will run but spits and sputters and backfires. If you "open it up" it falls on its face and stalls - but starts right up. Here is a link to an exploded view of the carb: Ohio Honda Yamaha Motorcycle ATV Dealer - J & J Motors - Kawasaki Suzuki Scooter Utility vehicle, parts, accessories, apparel
      Can anyone point me in the direction of the problem? It may still be a "clean carb parts issue" . My problem is that the parts list doesn't identify the parts to a degree that I understand. If you said" look at the pilot jet", I'm not sure which jet that would be....See what I mean? It'll run very good if I remove the air filter and cover the opening with my hand and part my fingers a little for the air to get in. Any help is greatly appreciated.
      Thanks in advance, Jim
    • By Matt John
      Charging issue?
      I have a 2017 Polaris Sportsman 570 EFI. Yesterday, I start the machine and it says low power (10.6-10.8). This machine is on its second battery. This is a new AGM battery with 50cca more than stock.
      Should I look at the regulator or stator?
      Thanks!!!
  • Similar Tagged Content

    • By Aaron Drost
      Hello bought my 2000 polaris sportsman 500 last week bike seems to work pretty good untill yesterday, when in reverse the bike seems to start bogging out? How come? 
    • By AimlessMoto
      Hey guys, new here, but haven't found ANY answer to my specific problem on a Suzuki dedicated ATV forum, so here's to hoping!
      I acquired a 95' Quadrunner 250, 4x4, (LT4WD) for practically nothing with no spark. The PO had tossed in a used stator which didn't fix the problem... so I went all routes (though cheaply) to narrow down the initial problem of no spark. 
      Plug, coil, CDI (caltric) and stator w/pickup (caltric) were purchased and installed. And it RAN, but bogged horribly and would not rev past 1/4 throttle. 
      I checked fuel flow, vacuum lines, all the normal stuff, no issues. I decided to check the valves and cam... well, there was one problem. The cam was 1mm under the lowest spec in the manual. So, in-came a new cam, Stage 1 Hotcams... also threw in a new set of shindy valves, lapped them, replaced the valve seals, and the timing chain. 
      Back together again (w/stock airbox and new oiled filter). Now it idles even better, still boggs at 1/4 throttle, but will rev past it if you hold the throttle open for a second. Ahaha... success!
      So I was able to ride it above 1/4 throttle once I had momentum... could shift through the gears, all was good as long as I kept it over 1/2 throttle. Took a long enough ride to break in the cam properly at least so I won't have to worry about that. 
      Now, I start fiddling with the carb. It's clean as a whistle, stock, with stock jets (new replacement Mikuni jets). Same problem. 
       
      I start thinking, maybe this is fuel related and the bike is having an issue transitioning from idle jet to main jet... so I LOWER the needle by raising the clip 1 spot. Now it revvs up in neutral with no bog, but it boggs about the same trying to ride it. So I move the needle down again with the clip on the top slot. Better, but still has a bit of bog at 1/4 throttle. 
      The last bit of advice I got was to ditch the CV carb... so I sprung for a brand new Mikuni VM30-83 round-slide. Bolted it up, blew into the vacuum tube to fill it with fuel (no vacuum port on this one) and she fired right up... but there is still a bit of bog, it's just masked by the fact that I'm not waiting for the vacuum diaphragm to open. 
       
      So I feel like each little step brings me closer, but not perfect. I'm now wondering if this is still in-fact a carb tuning issue (I have some jets I can fiddle with and maybe lean-out the idle jet a little.) OR if the cheap-a** Caltric Stator/Pickup is what's causing these issues. 
       
      I have a 95' KingQuad with 400 miles on it... like new.. runs like a top... I've tried both the stock QR and the Caltric CDI boxes on it, and it revvs up and runs like a champ. 
       
      The only unknowns between the two systems are the carb, and the stator/pickup. My next step in troubleshooting is to rip apart the King Quad and test it's CDI on the Quadrunner... but considering there is no change to how it runs I doubt it will lead to a solution. 
       
      HOWEVER... I tried the stock CDI just recently after running the Caltric this whole time, and the bike runs like garbage. Hardly idles, and won't rev up at all. So, that is my one smoking gun telling me that it's either the pickup coil or the stator itself. 
       
      Has anyone had a problem even CLOSE to this? I can't image the carb would be causing this many issues, especially going to 2 different ones, both with stock jetting to OEM, and exhibiting the identical symptoms... the only change is when different CDI's are plugged in, or when the needle valve leans out the mixture. 
      Also, I checked the piston, rings and bore when I had it apart and they're like-new... no scoring, rings are loose, cylinder is still round and has honing marks still int he bore. Stock piston, stock bore size and it has 160psi compression. Battery is brand new, and I've tried 3 different R/R's, none of which change any symptoms, but slightly vary the charging voltage by .2-.5 of a volt depending on which unit. Also tried a new coil which changed nothing. 
      ANY help would be appreciated. Too much invested to not get it running right. 
    • By BionicRival
      I have a 1997 Polaris Sportsman 500 4x4 that recently started bogging. Was riding down a road and all of a sudden started bogging. I tore the carburetor off, cleaned the jets , checked if there was spark. I'm pretty much out of ideas. After cleaning the carburetor, put it back on an now it wont start. Any ideas?
    • By petersty07
      Thanks to trent at trent signs and graphics for the awesome wrap!!
      [ame]
      [/ame]
    • By petersty07
      Thanks Trent at Trent Signs and Graphics for the awesome wrap!.
      [ame]
      [/ame]
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...