Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Bobs54

2005 Polaris Sportsman

Recommended Posts

Bought this, none of the battery wires are hooked up. Is there a red wrapped cable that hooks directly to the battery along with the one that goes to selenoid? They only show 1 in the diagram that goes to selenoid

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By gouletp
      Hi. When I press the starter switch, the solenoid clicks and the starter doesn't turn. The battery is good (about 12.6 volts).  I tried shorting the two big bolts on the solenoid with a screwdriver.  I got sparks and the starter didn't turn.  I tried running a booster cable directly to the starter post but all I get is a bunch of sparks.  I connected the positive side of the battery to the post or bolt on the starter.  I connected the negative side of the battery to the frame,  Did I connect everything wrong?  I don't know why I get the sparks.
      Thank you
    • By John Ford
      i ordered a keihin carb for my 07 trx 90 and it fits nicely but the new cable they sent is way too long and i can't make it work.  the old honda cable cap [that fits on top of the carb] is too small to fit.  the keihin cap is approx 3/4 or 19mm.  honda cap is more like 1/2 in.  the keihin has a rubber boot on the cap where the throttle cable goes through . i don't know how to find the right length [most cites don't give the length].  i'm not sure how cables fit into that boot  and do i need to add the length of the boot to the cable?  the old honda cable is 28 inches total, but the cable movement is only approx 2'' which would not be enough to reach the actuator block on the keihin.  looking to find a throttle cable compatible with the keihin.  any help, please.
       
       
    • By Admin
      View File 2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      Submitter Admin Submitted 06/29/2019 Category Arctic Cat ATV  
    • By w_r_e
      My scrap heap rescue '87 LT4WD has been running great until a couple days ago when the electric start started clicking instead of starting. Click is coming from the front so I got a new solenoid to try that (battery is showing 12.9 volts and is almost new so I doubt its battery). But like an idiot I pulled off the old wires without even noting what goes where.
      Now the battery cables I know, it lines up with the battery terminals. + on the right, ground on the  left if you're looking at the solenoid. But as for the the smaller wires that run to the starter switch, i have no clue. Help!
    • By Ed Zeppeli
      The play on my KQ 300 (1998) choke doesn't allow for the full movement downward on the thumb lever. So it goes about halfway down and if I push a little too far the cable pops out of the plastic setting it sits inside of. Then of course I have to take the control unit apart and put it back into position.
       
      Is it normal for the thumb lever to not go all the way down?
       
      I have no play left in the adjustment screw on the cable in the correct direction. The only play I have left would make it worse.
       
      It'a a new-to-me quad so I'm not sure if it's a replacement cable or OEM.
       
      Thanks
  • Similar Tagged Content

    • By oxidized_black
      tag : zukifreak
       
       
       
    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
    • By ut1w7b
      I have a 94 sportsman 400. It sat for several years before i got it. I have cleaned the carb it will start and run for about 5 min then it will flood. I have torn it down and cant see anything wrong. has anyone else ran into this problem any hel would be great.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...