Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

switch

95 250 timberwolf carb setting

Recommended Posts

I have a timberwolf that I love. It sat and the carb got gel from this wonderful ethanol. I cleaned it and put a new kit in it. it always started right off. now it cranks forever before it hits and then it will not idle. set according to instructions 23mm float, 4th notch on the pin, 1 1/2 turns out on the AIS. I have tried tweeking all of these some but nothing seems to make a difference. The biggest problem is that I got it back out because the wife has claimed this bike and now it will not run for her. Any help would sure get me out of a bind.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By JacobSlabach
      picked up this pos bike for $80 not running.  took it home, cleaned the carb and bypassed the fuse-  ran great (other than the rev limiter- those things are so stupid)  Then one day out of the blue it starts flooding on cold startup and wont idle cold, but idles to fast warm.  (too fast being about half throttle speed heh).  I tried a new carb ($10) and new sp.  new carb wouldnt make it run except on choke and then it was gushing white smoke.  I had better things to do with my time so I parked it in a shed and used it for a work bench for a while...  this last weekend, I wanted to take it along with the sportman to a mens retreat to let the younger boys have some fun on it--  took about 30mins to pull all the crap I had accumulated on it and then rolled it down to my workshop, put the old carb back on after adjusting the needle clip up two notches (leaner) and threw it back on the bike.  Will turn over, but no fire.  I didnt have time to check sp that day but just wanted some incite on what could be wrong with this quad (if it even qualifies as being called that)
    • By Wolds Alpacas
      Hello all.  I have just stripped down the carb on my YFM225 as it is not running right.
      I put it in the ultrasonic cleaner for half an hour and it has done a good job.
      Nice clean jets but when I go full throttle it backfires, and there is a lack of power.
      It also does not seem to take fuel in properly - it comes out the petcock ok so it is running freely enough, but it is not drawing into the carb.
      If anyone has any ideas I would be very grateful.
       
    • By KQ300cy
      Hi all, new to the forum, looking forward to getting some help/advice on maintaining an 18 yr old atv!  So my King Quad 300, recently started running really rough (otherwise ok til this point) at anything more than idle.  After started, choke on/off, doesn't seem to matter, it shutters (Not sure how else to explain it) really bad when given throttle.  I can let the engine run for several minutes, but this never improves.  
      Fuel pump checks out ok, and I don't see any gas in the fuel pump vacuum line.  I am a novice on a carburetor, but I need to see what's going on, so after taking it apart, I have a question about this plastic part with an o-ring that is above the jet needle.  Appears as if someone rebuilt this carb, because it is extremely clean...so I am wondering if this plastic part looks to be typical for this carb...or not.  Thanks in advance for the help!



    • By Ray Roberts
      Hey everyone im new here, i have a problem with my 2001 suzuki quadrunner 500. When i start the bike up it sounds fine but a few seconds later the idle speed just keeps rising to where you cant put it in gear, and if im lucky it will climb down to where i can put it in gear but when i press the gas it immediately want to die. Please help me!
    • By dcata
      Got a question and hopefully find some help. I have a 95 Timberwolf 250 that I picked up and it didnt want to idle. I have rebuild the carb with new kit replacing all the jets and float seat. Blew out the ports with the air compressor after I soaked the carb and cleaned the ports with a fine piece of wire and it still wont idle on its own. Has new air filter. I had it running and sprayed around the carb and carb joint and didnt get a rapid acceleration as if I had a leak. I read somewhere how the standard jets are like a number #40 and people have replaced them with a bigger jet. I called the local dealer here and they said they cant order jets and was wondering if this could be the problem and if so where can you order them at. Any info/help is highly appreciated. Sorry for being so long, just want to get as much info out as I can.
  • Similar Tagged Content

    • By fatfarmboy
      Just bought (Tue. evening) an '89 Suzuki 250 4wd that has been sitting out the last 5 yrs. It's complete, including the shift knobs, battery cover, and headlights. It has the optional cooling fan on it (probly stuck - didn't check), and the engine isn't locked up. Plastic looks good and isnt cracked. Racks aren't bent up. Shift lever works, the foot brake moves (needs oil - have to pull it up by hand), and there's black oil and no water in the engine sight glass. Guy was asking $125 and gladly took $100 for it. Anxious to get started on bringing it back to life. Been wanting one of these for years. As soon as I can get to it (working on a junky "Jackel" right now - Chinese Yamaha Timberwolf). I'm going to pull the tank off it and clean it, clean & possibly rebuild carb, put in new plug, and a battery, then see what happens. If nothing, will keep going until it runs. Feel free to respond if you want to, I'm mainly just excited and wanted to tell somebody. 
    • By Flanstone
      I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
    • By Christopher Williams
      Hello all, 
      i just rebuilt the top end of a 99 Bear Tracker 250 and it can’t get it to hit off of gasoline or starter fluid. Occasionally it will backfire. Right now I’m just trying to get it to fire off without the carburetor like I’ve done a thousand times before with other engines. Usually there is no response, but occasionally I get a backfire through the intake. ISeems like it’s out of time, but I don’t see how that could be possible. 
      Here’s what I know:
      1. compression 120psi
      2. all timing marks are lined up after numerous revolutions. 
      3. Strong spark. 
      4. Valves adjusted correctly. 
      Thanks in advance. 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...