-
Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
-
Similar Topics
-
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
-
By MarkinAR
What is the opinion on carb kits? What's one of the better brands of aftermarket? OEM is always preferred but not practical, chinese cheapie is never a good option.
Thoughts ?
-
By Bigal700
I got a 1994 yamaha timberwolf that 2 years ago i bought put carb on off a parts one had it running but not the best so i rebuilt the carb seemed to run good then i left it sit i wanted to ride it so,i took carb apart to clean it looked good had it running but wouldn't idle not a big deal then it died so i gave up on now trying to start wont do anything i checked spark looks good, has great compression and its getting gas i sprayed starter fluid in it and it still wont do anything what the heck could be wrong?
-
By Cj Winds
I have a 2000 Polaris Xplorer with the 250 two stroke motor
It does not want to start with the electric start, the motor cranks fast, the battery is good, and there is good spark when cranking. The engine starts perfect when using the pull cord, it even starts if I pull the cord slowly and starts with one pull. The engine idles smoothly once started. My wife says she needs the electric start to work.
-
By KINGSIZE
Howdy,
I was given a 2008 Yamaha Timberwolf by my in laws a few weeks back. Of course my FIL said it hasn’t run in 8 years but all it needs is gas and oil!
That hasn’t been the case...so far I’ve replaced the spark plug, changed air filter, replaced battery, replaced fuel and oil filters, fresh oil and gas. I tried starting her up and no luck, it turns over but won’t get going.
Now I’ve moved on to cleaning the carburetor which I’ve heard is a common problem area. I can’t figure out how to remove the bowl at the bottom, any suggestions? I removed the four screws that I thought were holding it in place but the bowl won’t budge
Thanks and looking forward to getting her running!
Some photos of what I’ve got going on , this has taken over the garage
-
-
-
Similar Tagged Content
-
By BosoxBruce
Recently I noticed gas leaking from under the gas tank on my 2005 250 2x4. As I looked closer it appears to be leaking from the shut off valve under the tank. It's the valve with the handle that can be turned to open, close or reserve. Can this part be replaced? Thank you.
-
By Derick Joel Smith Trimmings
Buying a Baja 250 tomorrow for 600 bucks, needs nothing but a wheel bearing, i already know Baja is an off brand crappier. Manufacturer, but does anyone have any tips or knowledge of these bikes?
-
By fatfarmboy
Just bought (Tue. evening) an '89 Suzuki 250 4wd that has been sitting out the last 5 yrs. It's complete, including the shift knobs, battery cover, and headlights. It has the optional cooling fan on it (probly stuck - didn't check), and the engine isn't locked up. Plastic looks good and isnt cracked. Racks aren't bent up. Shift lever works, the foot brake moves (needs oil - have to pull it up by hand), and there's black oil and no water in the engine sight glass. Guy was asking $125 and gladly took $100 for it. Anxious to get started on bringing it back to life. Been wanting one of these for years. As soon as I can get to it (working on a junky "Jackel" right now - Chinese Yamaha Timberwolf). I'm going to pull the tank off it and clean it, clean & possibly rebuild carb, put in new plug, and a battery, then see what happens. If nothing, will keep going until it runs. Feel free to respond if you want to, I'm mainly just excited and wanted to tell somebody.
-
By Flanstone
I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
-
By Christopher Williams
Hello all,
i just rebuilt the top end of a 99 Bear Tracker 250 and it can’t get it to hit off of gasoline or starter fluid. Occasionally it will backfire. Right now I’m just trying to get it to fire off without the carburetor like I’ve done a thousand times before with other engines. Usually there is no response, but occasionally I get a backfire through the intake. ISeems like it’s out of time, but I don’t see how that could be possible.
Here’s what I know:
1. compression 120psi
2. all timing marks are lined up after numerous revolutions.
3. Strong spark.
4. Valves adjusted correctly.
Thanks in advance.
-
-
Recently Browsing 0 members
No registered users viewing this page.