Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Wonderwoman

2003 manual shift 250 smoking issues

Recommended Posts

I am about at my wits end. Took the 250 back to the dealer repair shop AGAIN. Had it in there two months ago for a bad smoking issue. I thought it was to much fuel and washing the oil off the cylinder and burning it. They said it was the head. So I purchased new valves, valve guides, oil seals and had the head professionally done. So $225 later I had a great looking head. Well while I had the ATV apart this far I also got new rings for the piston. Mic'd everything out and everything was in spec. Put it back together and seemed like it smoked a little at the house (5000 feet above sea level). Took it to the mountains (9000 feet above seal level) for Sept. bear hunting and couldn't use it. Smoked worse than before and couldn't run it past half throttle or it would flood itself out. So brought it back home and it is back at the shop again. I say it is something in the carb that isn't set right or wrong jet????????? Anyone have any other ideas that it could be?

Share this post


Link to post
Share on other sites


is the smoke black or blue? black is gas and blue is oil, is it gas flooding or oil on the plug? was the cylinder in specs, even below the ring ridge line? did you hone it if it wasn't nickeled? is the crankcase vent line clear? just a few ideas

Share this post


Link to post
Share on other sites
is the smoke black or blue? black is gas and blue is oil, is it gas flooding or oil on the plug? was the cylinder in specs, even below the ring ridge line? did you hone it if it wasn't nickeled? is the crankcase vent line clear? just a few ideas

Smoke is blue, gas flooding is the symptom. Cylinder specd out great all the way. Cylinder walls were as smooth as can be and ran the hone down it one time. Never checked the crankcase vent line. Will do that. Found out that the jets are not correct. Dealer mechanic didn't think to check that until I said something. So we are going for correct jets and see what that does. I'll ask them to check the crankcase vent also. Thanks for your help.

Share this post


Link to post
Share on other sites
hate to say it but blue smoke is oil smoke,

You don't think the flooding of the carb could be washing the oil off the cylinder and burning it?????????////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Share this post


Link to post
Share on other sites


You don't think the flooding of the carb could be washing the oil off the cylinder and burning it?????????////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Ok, got the right jets for the carb and adjusted the valves. Smoke is gone and running great. Final test will be taking it to the mountains this weekend and see how it runs up there.:biggrin:

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By KJINTF
      Been slow in starting up, in the recent past it would start up in <1/2 second of the button press with a snap. Now it takes several seconds of cranking to get going. Once going runs as it always did. Replaced the plug no change. Battery is good.
      Before I tear it apart and look things over was hoping others might have had the same experience and have a quick fix for me
      Thanks in advance for any and all suggestions to get this old machine starting quickly again as it has for 20 years.  
    • By David Barsukoff
      Hey, I just bought the kids a LT80 and noticed a small puddle under the machine after they were riding it for a bit. I'm wondering if anyone knows why the fluid coming from the fuel shut off is a red colour, and would have any ideas of where this issue is coming from? I haven't had a real good look at it yet, thought I would ask first. 

    • By Harold Wallace
      mt. washington ride 2019 
       
    • By JacobSlabach
      recently picked up some project bikes off CL for cheap.  got a honda fourtrax (the ancient 4x4 kind with the straight axle in the front as well as the rear and a back-up kick-start)  plastics are crap, but my goal is to get running like a champ and patch the plastics up and sell to one of my many friends that want a reliable 4x4 for dirt cheap and doesnt care what it looks like.
      so the former owner says it needs carb rebuilt, but its sat for 3+ years since so who knows.  things I see:  carb is missing (he gave me a box of parts along with the bike), engine turns over and feels good with kick-start, brakes need work, battery missing (That always puts me off, cause then I know most likely someone's been tampering with the electrical.
    • By mrfartsalot
      i have a 2001 suzuki quadmaster 500 4x4 that the primary cvt clutch is rusted on any ideas on how to get it off i want to try to reuse it if possible.
  • Similar Tagged Content

    • By Chayse Hill
      I have a 2003 LTZ 400 that i bought a few days ago. The quad was running fine until last night. I let my brother ride it down the street and back and i didnt notice anything etong with bike. Then my neighbors friend came over and said "can i ride it?" I said "sure" so he ripped it down the road all fine and when he got back it died right in front of us. My brother said it was dieing on him also. He also said that he wasnt using the clutch to shift. I told him he was an idiot. Im throwing that in there incase that caused a problem as well. But today i go to check it to make sure its getting fuel which it is and replaced the spark plug incase it wasnt getting spark but it is. So i started it and it was having a problem starting then i got started and was reving at idle high. So i took it around the block and it died on me a little bit down, so i try to restart it and it started so i kicked it into 1st and it kinda launched on me and started going with the clutch all the way in. Then it died right after and wasnt running right during that process and was idleing all over the place and just died and now i cant get it started it again. Before it would start without the choke or priming it. It would start real quick now i cant figure if it needs to be rejetted or something else. Air filter looks clean also. But any help would be gratelly appreciated!
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...