Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

frankmako

2005 Arctic Cat 500 Leaking Fuel From Top Of Carb

Recommended Posts

My 2005 Arctic Cat 500 started leaking fuel from the top right hand side of the carb. It looks and feels that the fuel is coming from under the throttle cable housing area just above the primer pump. I have not had time to take carb off. Has anyone had a leak on this side and area of their carb?

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By AimlessMoto
      Hey guys, new here, but haven't found ANY answer to my specific problem on a Suzuki dedicated ATV forum, so here's to hoping!
      I acquired a 95' Quadrunner 250, 4x4, (LT4WD) for practically nothing with no spark. The PO had tossed in a used stator which didn't fix the problem... so I went all routes (though cheaply) to narrow down the initial problem of no spark. 
      Plug, coil, CDI (caltric) and stator w/pickup (caltric) were purchased and installed. And it RAN, but bogged horribly and would not rev past 1/4 throttle. 
      I checked fuel flow, vacuum lines, all the normal stuff, no issues. I decided to check the valves and cam... well, there was one problem. The cam was 1mm under the lowest spec in the manual. So, in-came a new cam, Stage 1 Hotcams... also threw in a new set of shindy valves, lapped them, replaced the valve seals, and the timing chain. 
      Back together again (w/stock airbox and new oiled filter). Now it idles even better, still boggs at 1/4 throttle, but will rev past it if you hold the throttle open for a second. Ahaha... success!
      So I was able to ride it above 1/4 throttle once I had momentum... could shift through the gears, all was good as long as I kept it over 1/2 throttle. Took a long enough ride to break in the cam properly at least so I won't have to worry about that. 
      Now, I start fiddling with the carb. It's clean as a whistle, stock, with stock jets (new replacement Mikuni jets). Same problem. 
       
      I start thinking, maybe this is fuel related and the bike is having an issue transitioning from idle jet to main jet... so I LOWER the needle by raising the clip 1 spot. Now it revvs up in neutral with no bog, but it boggs about the same trying to ride it. So I move the needle down again with the clip on the top slot. Better, but still has a bit of bog at 1/4 throttle. 
      The last bit of advice I got was to ditch the CV carb... so I sprung for a brand new Mikuni VM30-83 round-slide. Bolted it up, blew into the vacuum tube to fill it with fuel (no vacuum port on this one) and she fired right up... but there is still a bit of bog, it's just masked by the fact that I'm not waiting for the vacuum diaphragm to open. 
       
      So I feel like each little step brings me closer, but not perfect. I'm now wondering if this is still in-fact a carb tuning issue (I have some jets I can fiddle with and maybe lean-out the idle jet a little.) OR if the cheap-a** Caltric Stator/Pickup is what's causing these issues. 
       
      I have a 95' KingQuad with 400 miles on it... like new.. runs like a top... I've tried both the stock QR and the Caltric CDI boxes on it, and it revvs up and runs like a champ. 
       
      The only unknowns between the two systems are the carb, and the stator/pickup. My next step in troubleshooting is to rip apart the King Quad and test it's CDI on the Quadrunner... but considering there is no change to how it runs I doubt it will lead to a solution. 
       
      HOWEVER... I tried the stock CDI just recently after running the Caltric this whole time, and the bike runs like garbage. Hardly idles, and won't rev up at all. So, that is my one smoking gun telling me that it's either the pickup coil or the stator itself. 
       
      Has anyone had a problem even CLOSE to this? I can't image the carb would be causing this many issues, especially going to 2 different ones, both with stock jetting to OEM, and exhibiting the identical symptoms... the only change is when different CDI's are plugged in, or when the needle valve leans out the mixture. 
      Also, I checked the piston, rings and bore when I had it apart and they're like-new... no scoring, rings are loose, cylinder is still round and has honing marks still int he bore. Stock piston, stock bore size and it has 160psi compression. Battery is brand new, and I've tried 3 different R/R's, none of which change any symptoms, but slightly vary the charging voltage by .2-.5 of a volt depending on which unit. Also tried a new coil which changed nothing. 
      ANY help would be appreciated. Too much invested to not get it running right. 
    • By David Barsukoff
      Hey, I just bought the kids a LT80 and noticed a small puddle under the machine after they were riding it for a bit. I'm wondering if anyone knows why the fluid coming from the fuel shut off is a red colour, and would have any ideas of where this issue is coming from? I haven't had a real good look at it yet, thought I would ask first. 

    • By John Ford
      i ordered a keihin carb for my 07 trx 90 and it fits nicely but the new cable they sent is way too long and i can't make it work.  the old honda cable cap [that fits on top of the carb] is too small to fit.  the keihin cap is approx 3/4 or 19mm.  honda cap is more like 1/2 in.  the keihin has a rubber boot on the cap where the throttle cable goes through . i don't know how to find the right length [most cites don't give the length].  i'm not sure how cables fit into that boot  and do i need to add the length of the boot to the cable?  the old honda cable is 28 inches total, but the cable movement is only approx 2'' which would not be enough to reach the actuator block on the keihin.  looking to find a throttle cable compatible with the keihin.  any help, please.
       
       
    • By colin james
      View File 2005 Polaris Predator 50/90 Sportsman 90 Service Manual
      This is the factory service manual for the 2005 predator 50cc and 90cc, Sportsman 90cc. Download all the chapters for the complete manual or just the sections you need.
      Submitter colin james Submitted 04/06/2019 Category Polaris ATV  
    • By Coral Breding
      I loosened the allen bolts on the carrier and when I went to put my driver in the alot to pull back and tighten the chain, I noticed the holes were facing the front of the bike. I tried to slide a driver in and tighten the chain but the thing would not budge. I nearly ripped the tip off the driver in the slot. Any suggestions? 


  • Similar Tagged Content

    • By oxidized_black
      tag : zukifreak
       
       
       
    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...