Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Mo Salem
So my front hub broke, I’d like to put aftermarket on. Hard to find new oe ones. Please help. I’m new to all of this, I have some car knowledge and try to apply it
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
I am new to this forum and hope that someone out there can help me, I have an early Suzuki King Quad 300 (280cc) which starts intstantly every time but at about half revs or there abouts it starts spluttering and will not rev any higher, this fault is present whether choke is applied or not, some one suggested that silencer maybe be clogged so removed baffle but no improvement have removed carb and stripped 3 times but still no joy.
Any ideas would be most welcome.
1987 Suzuki LT 80 and 2007 Honda CRF 50 dirt bike stolen out of my driveway on July 4th. Anyone with info that recovers them will get $400 no questions asked.
The post Suzuki LT 80 Quad And Honda Dirt Bike appeared first on STOLEN 911.
View the full article
Similar Tagged Content
This is my first post and I was wondering if there is anyone who can help me solve a problem I have with my Yamaha Kodiak 400 4x4 Fitted with a Mikuni Carburetor . The year of the quad is around 1998, the reason I am not sure of the date is, there wasn't any paperwork and no details on the frame either.
The quad had a bad leak from the carb overflow which indicated that the float needle valve was blocked or passing so I replaced this and put everything back together. The quad ran really well until I took it onto some rough ground to have a ride around, a few hours later the engine started to run really rough as if the engine was flooding. I have removed the carb again and cleaned the needle valve out and the whole of the carb just in case there where any dirt behind it. Engine now runs fine again but fuel has started to run out the carb overflow again.
I have tried everything to try and stop the fuel leaking out the overflow but its still happening. My last thoughts where to adjust the float level and its still happening.
Has anyone got any thoughts on the problem or could suggest whats causing the fuel leaking out the overflow.
Thanks for reading
Just curious if anyone ever tried to fit a 99-09 bruin 250 muffler on an older moto 4 250 before ?
Looks like it would . Probably not to hard to adapt the mounts . Just wondering about clearance as the one we have just barely clears the tire .
Thanks in advance .
Hello, well back to where I was last year with this carb. Took my 250 to the mountains for the first time this year and blue smoke, too much gas again. I can't believe that this carb gives me this much trouble. Seems like the choke is stuck but the cable moves freely. Anyone else ever experience this issue? Do you think a new choke cable would maybe resolve this?http://www.quadcrazy.com/atvforum/images/smilies/arghh.gif
OK it was the choke. Put on all new cable and plunger and she is running 100% again. So now the question is, is the carb getting worn out where the plunger needle goes in the small hole and when I use the choke the needle end doesn't get lined back up with the hole?? We'll see how it runs and now that I know what the issue is I can always pull the choke plunger out and reinstall if I start having this issue again.
Recently Browsing 0 members
No registered users viewing this page.