Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

gyminis

grizzly 700 fuel pump

Recommended Posts

HELP, i have a 2009 yamaha grizzly 700 yfm7fgpy special edition with a defective fuel pump and am wanting to know how to test it to know if it is defective or not

Edited by gyminis
more information

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ajmboy
      Disconnected the plow yesterday on my 2004 Yamaha Grizzly 660 and am getting ready to do some riding yesterday and the battery went weak, Starter cranked a few times but week. Put my trickle charger on that I bought and went to the garage today to start it up, but the starter is just spinning and not engaging. The solenoid is clicking. The pull start sucks and is hard to pull (never use it and need to look into that). Quick video of the starter spinning. Could it be the starter or  the starter clutch one-way bearing? I guess I need to take the cover off to see what's going on.

      2004 Yamaha Grizzly 660 Starter Spinning.mp4
    • By StolenATV
      My Children’s 50CC Yamaha ATV was stolen from just outside the garage. I did a little custom work to the front of it and added two LED headlights to it as well as a switch to the plastic handle bar cover. Our home sits well off the road and it was not something that was just in plane site so my fear is that this was planned over time and the thieves knew we had it and were just waiting their chance. We also had a 20 inch bike that was stolen as well, we were able to recover it however about a mile down the road as it was left abandoned. We didn’t know it, but we think the bike may have been taken a few days earlier. Now sure if both items were taken by the same person or just a coincidence Thanks for any help you might be.
      The post Yamaha 50 CC Raptor ATV Stolen appeared first on STOLEN 911.
      View the full article
    • By Orangejbird
      My Dad's 03 Manual Vinson has milky oil. He changed oil and ran it everyday for a week being sure to keep it running for an hour each time. Fresh oil is getting milky again..
      Thinking it's the water pump seal. Has anyone here successfully changed the seal or even replaced the whole pump assembly?
    • By Bleuu
      Hello so I’m new to the atv seen, and was wonder why my stock light didn’t turn on , and it figures that the black and white wire and the black wire were ripped apart everything else is connected fine, what could to reconnect them
  • Similar Tagged Content

    • By mikeexplorer
      Wiring diagram for 2007 Arctic Cat 700 EFI 4x4
       
       
    • By Admin
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
    • By Admin
      View File 2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      Submitter Admin Submitted 06/29/2019 Category Arctic Cat ATV  
    • By x
      It's time to replace the shocks and struts.  Looking for some stiffer springs than the OEM as I use this for farm work and I put heavy loads on the rear and haul small trailers frequently.  I've seen a couple aftermarket offerings that say they're 10% or so heavier duty.  Any other options for something a little stronger / stiffer?  Thanks.
    • By LMI
      The saga of the fan continues.
      The Pin attempt in the fan shaft failed.  I then moved on to trying to weld the fan hub to the fan shaft.  I took it for a run the weld broke.  Now it was truly F'ed.  To recap the dealer price, they want $400 + CND for a replacement fan assembly.
      I searched all sorts of after market places and no one carried one.  Ebay had some used ones but they were $120 USD + Conversion rate for something as old as what I have.  I went to Amazon and eventually settled on this.
       
      amazon link
       
      What I found... and was amazed... was that the fan mounted to the Suzuki fan assembly bracket.  I was prepared to manufacture my own mount conversions...  It also came with "Harpoon mounts" (nylon zip tie like things that go straight through the rad.   Anyways it mounted to the original bracket. It fit perfectly.  Cut the electrical plug off replaced it with the Suzuki... all good.  Let the quad heat up, thermo coupler kicked in the fan circuit, polarity was right... all was good....  Fan is under the circuit fuse rating.  
       
      so I finally have a solid fan solution.  $34 CND vs $400+ CND
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...