Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

fambler4

polaris back brake?

Recommended Posts



I'm not familiar with the Polaris, but I think it's got a master cylinder at the brake handle. Fill up the master to the top, close it. Have someone pump the brake pedal and hold it. Loosen the bleeder slowly to remove air (at the brake caliper, or center). The pedal will sink. Close the bleeder. Pump it up again until the pedal is hard and hold it. Loosen the bleeder to remove air and the pedal will sink again. Close it and check the fluid level. Repeat these steps until you are confident you have a good pedal.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dimelol
      I have a 2003 Kodiak 450 that i purchased a while back with around 300 hours on it. It has never ran right from the beginning. Initially i thought it was just a carburetor issue because it was all clogged up from sitting for months. It has been cleaned, rebuilt, and taken off probably about 10 times troubleshooting this problem. I have quadruple checked everything including float height ect and it is set correctly, the jets are also brand new, needle and seat have been pressure tested as well. So after all of that I am convinced that the carburetor is not the culprit. I have an issue where the idle is very choppy, almost as if it is misfiring with a rich condition on top of that. I can use a brand new plug and run the machine for just a few minutes and it will be a dry and and coated in black carbon build up. The exhaust also has a strong smell at idle. I had trouble restarting it when hot for a while, but i adjusted the valves and it seemed to solve that issue. They were both way out of tolerance (tight). The weird thing is, outside of idle it seems to run pretty well. 
      So with all that being said I have ruled out the carb/valves/compression and moved on to the ignition and this is where i have a few questions about factory specifications. I guess the main question I have is, how strict are these tolerances? And could them being off by this amount cause the issue I am having? Do all three of these parts really need to be replaced? I would like to know before I spend the money on these new parts, and it not fix my problem. Below I will list what the specs were in the service manual along with the reading i got.  This is my first experience testing ignition components. I just found it odd that all 3 are out of spec according to the service manual.
      Spark plug cap resistance: 10 kΩ at 20 °C (68 °F)
      My Reading: 8.90 kΩ
      Primary coil resistance: 0.18 ~ 0.28 Ω at 20 °C (68 °F)
      My Reading: Fluctuated between 0.4 - 0.5 Ω
      Secondary coil resistance: 6.32 ~ 9.48 kΩ at 20 °C (68 °F)
      Reading was within the specified range.
      Pickup coil resistance: 459 ~ 561 Ω at 20 °C (68 °F)
      Reading was within specified range.
      Rotor rotation direction sensing coil resistance: 0.085 ~ 0.105 Ω at 20 °C (68 °F) 
      My reading was 0.3 Ω
    • By utvboard
      Introducing the Dash Frame system for the Kawasaki Teryx from Black Rhino Performance. The Dash Frame fits nicely into the middle of your dash, and is designed to closely follow the shape of the Kawasaki Teryx dash. This frame puts your gauges and switches at the same angle as the upper dash for easy viewing of the gauges and convenient placement of switches. The panel provides mounting for 3 2"
      https://www.utvguide.net/dash-frame-system-for-the-kawasaki-teryx-now-available/
    • By Azrial
      I just picked up a 2008 Kawasaki Teryx 750 LE 4x4 and am looking for Wench Suggestions. It was used by an old man to check his mail and only has 30 hours on it! I intend to use this on my very steep property like a small tractor. I had a old Ford 1220 Tractor and with its high center of gravity and lack of 4 wheel drive it was useless!

      To the point, I am looking a wench suggestions to help my new tool do its job! Even though the front bumper is drilled for a wench, I understand that I need a wench plate and that some wenches will not fit without body mods. Does 3500 Lbs capacity sound right?

      Thanks!
    • By Resurgence Small Engine Inc.
      In this video, Jonathan diagnoses & repairs the decompression system on a Yamaha 2003 Grizzly 660.
      Some symptoms include: Pulling recoil right out of your hand, starter turning really slowly, constant dead batteries.
      Thanks for watching!
       
    • By Ajmboy
      I'm doing some work at my house this spring and will need to rake out about 1/2 an acre of ground because the fill comes with rocks and such. Has anyone used a rake they like or created something cool that works? Home depot has a Kolpin for $275.

  • Similar Tagged Content

    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By Beb1041
      Looking for a download of a manual
    • By warkcol
      I am having an issue where it sounds like the gears are slipping if I hit the throttle really hard and also after letting off when the engine brake is applied. Also, the drive train that goes to the front also rides again the gear shift box. I will attach pictures and a video here shortly.
      Thanks in advance!
      [ame]
      [/ame]https://postimg.org/image/cdlu6fza9/
    • By Weldingrod47
      Trying to change front wheel bearings. I removed the cotter pin and castle nut. Hub won't budge. Is there an additional retaining clip? Seems to be one of those push on type that barbs on the thread of the spindle. How do I remove it?
    • By buzzar56
      I am looking for a free repair manual for a 2003 Polaris sportsman 500 ho atv. all the posts on here lead me noplace
      thanks fred.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...