Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

gyminis

2009 grizzly 700 starts but doesnt stay running

Recommended Posts

i have a 2009 grizzly 700,replaced the fuel pump and filter,replaced the spark plug and checked the air filter for a mouse house! it runs then shuts down,wont stay running,does the fuel line need to be primed and air free to run properly or am i missing something obvious??????????????:aargh:

Edited by gyminis
more info

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tahj
      I am looking to see why my 2005 Grizzly  660 won't crank. I have set the valves but suspect a loose timing chain.
      When working to remove the valve cover I found a "cap tensioner case" - parts #25  - #299 on Babbitts site.
      The  cover seems to bridge the valve cover and the cylinder head. What the hell is it and what surprises will I  find if I remove it?
      Uncharted territory for me.
    • By David Cameron
      The small waterline insert for the hose that goes from the water pump cover to the thermostat housing has corroded off. I only need the insert on top and behind the thermostat housing that the hose goes over and can't find just the insert. It looks like it may be pressed in. I've have been told the entire motor housing needs to be replaced. The pic with the red line indicates where the hose and insert would be and the insert looks like the pic of the water pump  Any ideas would be really appreciated.
       
       



    • By Frank Angerano
      Take a look at this.  Curious about everyone’s input.it looks pretty good.   We all have this common problem of accessing the air fuel mixture screws.    
      The reviews look pretty good.  I may order one just to see how it works out.
       
      https://www.motosport.com/rd-flex-jet-fuel-mixture-screw
      They also have other types that will work on this site.  
    • By David Land
      About 6 months ago I had a new fuel pump, ECM, stator and heaven only knows what else installed on my 05 King Quad.  It has been running great until the other day when I went to get it off the trailer, and it would not start.  Pulled the plug, and it was a little dirty, but not bad, but I put a new one in just for good measure.  Still would not start.  Pulled the fuel line connector underneath and turned on the switch and fuel was coming out, but with little to no pressure.  I turned the switch off and on multiple times to fill up a water bottle with fuel, and the fuel was good.  As it turns out, the fuel pump is out of warranty (go figure).  So, I'm going to put a pressure gauge on it tomorrow and see what it is pumping.  Is there anything else I can check?
      Many thanks,
       
      David
    • By Tahj
      I bought a "project" Grizzly 660, I think it has been a few people's project. The PO had it for a while and did not have time to work on it. He said the battery was good, but I don't know how he knew because the display was blank, no lights and won't crank or run. 
      I found a nest under the front cover, by the CVT inlet, a chewed thru wire and a few more without insulation. Rewired those from the connector (black 3 wire to the display) and replaced the fuse as suggested by a search from this site. That got the display working and power to other circuits. 
      I replaced the aftermarket start switch with a used OEM switch from eBay. Then it would crank a little, and started once for a few seconds. 
      I'm a small engine mechanic - mowers, snow blowers, etc. In my small engine work I have had a number of rider mowers that would crank about a half turn and then stop. The owners have suspected a bad battery and changed it with no improvement. Setting the valves to spec usually fixed this.

      I set the valves on the Grizzly without solving the crank problem. I wonder if the timing chain could be off - slipped a tooth. 
      I don't know any way to check for this without pulling the head and looking at the timing marks on the cam gear. 
      Is there another way to check for proper timing?
       
  • Similar Tagged Content

    • By bodatiouskid
      Have a 2002 Polaris Sportsman 700 that only has 34mi. on a carb & ring job.
      Cut the gas off today to drain carb.Now engine will not idle.If I open throttle will run,but let off & will cut off.Can screw idle in with no change.
      What happened? Why did this happen when fuel ran out?
      Please help me,my ATV is a daily driver.
      Please help!!
    • By toonces
      I'm wanting to run Shell Rotella T6 synthetic in the 700 Griz but I can only find it in either 0W-40 or 5W-40 weights, and the manual says it's ok to use everything BUT those weights...5W-30, 10W-30, 10W-40, 15W-40, 20W-40 and 20W-50.
      Would it be ok to use the Rotella 5W-40 or do I need to stick to what's specified in the manual?
    • By gyminis
      HELP, i have a 2009 yamaha grizzly 700 yfm7fgpy special edition with a defective fuel pump and am wanting to know how to test it to know if it is defective or not
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...