Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

bodatiouskid

2002 Sportsman 700 wont idle.

Recommended Posts

Have a 2002 Polaris Sportsman 700 that only has 34mi. on a carb & ring job.

Cut the gas off today to drain carb.Now engine will not idle.If I open throttle will run,but let off & will cut off.Can screw idle in with no change.

What happened? Why did this happen when fuel ran out?

Please help me,my ATV is a daily driver.

Please help!!:frown:

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Gary Patch
      Hi my linhai 300 is hard to start and  engages gears at idle which is 1200 rpm was looking at cdi says on it 7500 rpm does this mean quad should idle at 7500 rpm as this would explain transmission problemb as idle is too high thanks gary
    • By AimlessMoto
      Hey guys, new here, but haven't found ANY answer to my specific problem on a Suzuki dedicated ATV forum, so here's to hoping!
      I acquired a 95' Quadrunner 250, 4x4, (LT4WD) for practically nothing with no spark. The PO had tossed in a used stator which didn't fix the problem... so I went all routes (though cheaply) to narrow down the initial problem of no spark. 
      Plug, coil, CDI (caltric) and stator w/pickup (caltric) were purchased and installed. And it RAN, but bogged horribly and would not rev past 1/4 throttle. 
      I checked fuel flow, vacuum lines, all the normal stuff, no issues. I decided to check the valves and cam... well, there was one problem. The cam was 1mm under the lowest spec in the manual. So, in-came a new cam, Stage 1 Hotcams... also threw in a new set of shindy valves, lapped them, replaced the valve seals, and the timing chain. 
      Back together again (w/stock airbox and new oiled filter). Now it idles even better, still boggs at 1/4 throttle, but will rev past it if you hold the throttle open for a second. Ahaha... success!
      So I was able to ride it above 1/4 throttle once I had momentum... could shift through the gears, all was good as long as I kept it over 1/2 throttle. Took a long enough ride to break in the cam properly at least so I won't have to worry about that. 
      Now, I start fiddling with the carb. It's clean as a whistle, stock, with stock jets (new replacement Mikuni jets). Same problem. 
       
      I start thinking, maybe this is fuel related and the bike is having an issue transitioning from idle jet to main jet... so I LOWER the needle by raising the clip 1 spot. Now it revvs up in neutral with no bog, but it boggs about the same trying to ride it. So I move the needle down again with the clip on the top slot. Better, but still has a bit of bog at 1/4 throttle. 
      The last bit of advice I got was to ditch the CV carb... so I sprung for a brand new Mikuni VM30-83 round-slide. Bolted it up, blew into the vacuum tube to fill it with fuel (no vacuum port on this one) and she fired right up... but there is still a bit of bog, it's just masked by the fact that I'm not waiting for the vacuum diaphragm to open. 
       
      So I feel like each little step brings me closer, but not perfect. I'm now wondering if this is still in-fact a carb tuning issue (I have some jets I can fiddle with and maybe lean-out the idle jet a little.) OR if the cheap-a** Caltric Stator/Pickup is what's causing these issues. 
       
      I have a 95' KingQuad with 400 miles on it... like new.. runs like a top... I've tried both the stock QR and the Caltric CDI boxes on it, and it revvs up and runs like a champ. 
       
      The only unknowns between the two systems are the carb, and the stator/pickup. My next step in troubleshooting is to rip apart the King Quad and test it's CDI on the Quadrunner... but considering there is no change to how it runs I doubt it will lead to a solution. 
       
      HOWEVER... I tried the stock CDI just recently after running the Caltric this whole time, and the bike runs like garbage. Hardly idles, and won't rev up at all. So, that is my one smoking gun telling me that it's either the pickup coil or the stator itself. 
       
      Has anyone had a problem even CLOSE to this? I can't image the carb would be causing this many issues, especially going to 2 different ones, both with stock jetting to OEM, and exhibiting the identical symptoms... the only change is when different CDI's are plugged in, or when the needle valve leans out the mixture. 
      Also, I checked the piston, rings and bore when I had it apart and they're like-new... no scoring, rings are loose, cylinder is still round and has honing marks still int he bore. Stock piston, stock bore size and it has 160psi compression. Battery is brand new, and I've tried 3 different R/R's, none of which change any symptoms, but slightly vary the charging voltage by .2-.5 of a volt depending on which unit. Also tried a new coil which changed nothing. 
      ANY help would be appreciated. Too much invested to not get it running right. 
    • By John Ford
      i ordered a keihin carb for my 07 trx 90 and it fits nicely but the new cable they sent is way too long and i can't make it work.  the old honda cable cap [that fits on top of the carb] is too small to fit.  the keihin cap is approx 3/4 or 19mm.  honda cap is more like 1/2 in.  the keihin has a rubber boot on the cap where the throttle cable goes through . i don't know how to find the right length [most cites don't give the length].  i'm not sure how cables fit into that boot  and do i need to add the length of the boot to the cable?  the old honda cable is 28 inches total, but the cable movement is only approx 2'' which would not be enough to reach the actuator block on the keihin.  looking to find a throttle cable compatible with the keihin.  any help, please.
       
       
    • By colin james
      View File 2005 Polaris Predator 50/90 Sportsman 90 Service Manual
      This is the factory service manual for the 2005 predator 50cc and 90cc, Sportsman 90cc. Download all the chapters for the complete manual or just the sections you need.
      Submitter colin james Submitted 04/06/2019 Category Polaris ATV  
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
  • Similar Tagged Content

    • By Jean de la Chevrotière
      View File Polaris 700 2002 Owner's manual
      Polaris 2002 700 Owner's Safety and maintenance manual
      Submitter Jean de la Chevrotière Submitted 12/01/2018 Category Polaris ATV  
    • By Jean de la Chevrotière
      Polaris 2002 700 Owner's Safety and maintenance manual
    • By priglmeier
      I own a 2002 Can-Am Quest 650.
      It will start if you massage the throttle a bit and it will continue to run. BUT if you let go of the throttle and try to let it idle it will always die warm or cold.
      It has Non-Oxy premium gas, a new gapped NGK plug, a new carb (as of today) and fresh fluids. After installing the new carb it runs exactly the same.
       
      I only have a few things that I have observed since the new carb:
      The choke still doesn't do anything. It has a good cable and it is hooked up. It on fully off. There is a cable in the top, front of the engine that splits into two connectors. The connected side is in the photo. The other side has the yellow banded section and is not connected. I do not see anything in range of this connector so I don't know if this is normal or not??? The original carb wasn't really dirty or clogged. I'll use it as a spare. I don't see this cable and connectors listed in the Can-Am shop manual. Looking for some help. I want to ride!


    • By petersty07
      Thanks to trent at trent signs and graphics for the awesome wrap!!
      [ame]
      [/ame]
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...