Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Kyboy

Help with 2006 Honda Recon 250 Rear Brakes

Recommended Posts

Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate

Share this post


Link to post
Share on other sites


Where you able to get this done? Sometimes a couple of whacks with a soft blow hammer will do the trick.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By caperwing
      The rear brakes on this are hydraulic and manual. The hydraulic part is all messed up so I disconnected it all and want to go just manual on the rear. I got it all put back together but doesn't seem to work to well, like not enough pressure. The manual says I should mark the casing before taking it apart which I didn't read until to late. Any ideas? I put new brake pads on.
    • By Jeff011366
      Hello,
        Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
       
        My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires....  Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
        It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
       
      Thank you in advance for sharing your knowledge.
      Jeff
    • By Azrial
      I just picked up a 2008 Kawasaki Teryx 750 LE 4x4 and am looking for Wench Suggestions. It was used by an old man to check his mail and only has 30 hours on it! I intend to use this on my very steep property like a small tractor. I had a old Ford 1220 Tractor and with its high center of gravity and lack of 4 wheel drive it was useless!

      To the point, I am looking a wench suggestions to help my new tool do its job! Even though the front bumper is drilled for a wench, I understand that I need a wench plate and that some wenches will not fit without body mods. Does 3500 Lbs capacity sound right?

      Thanks!
    • By Monika Novakov
      1988 Kawasaki 220 Bayou trying to remove generator/ starter 1way clutch cover to be able to replace 1way clutch. All bolts are removed case cover is dripping what oil that remains...but I can't get the cover to come off..what am I missing? Thx in advance.
    • By Ed Zeppeli
      I have some wobble in my right rear wheel. Too much wobble.
       
      So I've torn into it and will need two bearings and two (different) seals. I'd like to get them locally if possible but need to know the number on the sides of the bearings and seals as I don't know that my bearing shop can source them by vehicle model. I'm told they're very common bearings.
       
      Any idea what the numbers are if mine end up being illegible?
       
      Thanks,
       
      Warren
  • Similar Tagged Content

    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By chuckcnm
      Hi, just picked up a MOTO 4 YFM255 and want to replace the rear brake pads. How do I get to the back. Guessing I need to remove the brake disk, question any easy way to do this?
      Thanks
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By pickytar
      I have a Chinese Hybird 250 or that's what I was told it was. I found 17 numbers on the frame. Will these numbers tell me exactly what it is that I have? (I know that its a 2006 from a plate on the front)
    • By Beb1041
      Looking for a download of a manual
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...