Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
ATVNetwork

Mac's ATV Wheel Net Pack

Recommended Posts



Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Forum Topics

    • 6 Products You Will Be Thankful For In The Fall

      news Keeping the ride going in the fall with the right gear As the fall weather sets in you will be thankful for gear like this when the temperature drops. View the full article

      By ATVNetwork, in ATV News, Articles & Press Releases

      • 0 replies
      • 56 views
    • New Polaris Ranger 2" Front Receiver from Extreme Metal Products

      Extreme Metal Products has released their new 2" Front Receiver for 2009-2010 Polaris Rangers. This mounts inside your stock front bumper. This allows you to insert a standard 2" square receiver hitch or a multi mount winch plate on the front of your Polaris Ranger. Made from .188 inch thick American steel this unit is very heavy duty. Simply, bolts inside your stock front bumper. No More...

      By utvboard, in Polaris UTV Forum

        
      • 1 reply
      • 1,652 views
    • Wheel Studs - 1994 4WD Timber Wolf

      Anybody have a part number for these or are they only available as an entire hub assembly. I have 2 broken and I was able to get 2 loose from Auto Zone. Even though they fit the lug nut, the knurled part of the stud is smaller than the factory ones and they spin until friction takes effect when tightening the nut. The ones they sell are a M10-1.25. Also any advice on the wheel dust caps? On Yamaha parts, there are 2 parts list for this model with 4 wheel drive. One shows nothing while one shows a part number of 52H-2512A-00-00. I'm wondering how durable and well they fit. My son game me 4 with a part number of 5GT-2512A-00. Those fit on the wheels but they seem like they will fall off on the first bump.  Before I spend $48 dollars on dust caps, I want to make sure I won't lose them on the trail. Thanks in advance.

      By CJ River Rider, in Yamaha ATV Forum

      • 0 replies
      • 95 views
    • How to set wheel alignment.

      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways. Here's some of the tools you will need... 1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway. 2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods. 3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels. 4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands. 4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench. 5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done! Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components. For this wheel alignment I'm using the Polaris Specs which seems to be a common setting. Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel. 6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement. 7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string. 6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches. 7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy. The whole process only takes about 15-20 min.

      By PolarisRich, in Polaris ATV Forum

        
      • 3 replies
      • 13,102 views
    • 84 Honda TRX200 front wheel cylinder

      Hello everybody, I am looking for a source for front brake wheel cylinders. Mine are shot. Are there any aftermarket manufacturers out there? Thanks ahead of time

      By Ineedabrew, in Honda ATV Forum

      • 6 replies
      • 335 views
  • Recently Browsing   0 members

    No registered users viewing this page.


×