Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

dirtybear00

Need info on manual shift 2000 big bear 400 4x4

Recommended Posts

I have a 2000 big bear 400 manual shift. Does not have a shift lever on gender like a Kodiak has left foot operated rn12345 on left foot lever. I replaced the stator and pick up coil and now it is difficult to shift. I marked (indexed) the lever, rod and pivot clamp prior to removal and not sure where to go .  Maybe a clutch adjustment ? Anyone have a manual for this model ? I was sent a manual but it is for a shiftless Kodiak yet it states big bear as well 

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By flyinbrian365
      View File 2018 Textron Stampede 4x4 Service Manual
      2018 Textron Stampede 4x4 Service Manual
      Submitter flyinbrian365 Submitted 09/07/2018 Category Textron Off Road UTV  
    • By Admin
      View File 2018 Textron Stampede 4 Owner's Manual
      2018 Textron Stampede 4 Owner's Manual
      Submitter Admin Submitted 04/09/2020 Category Textron Off Road UTV  
    • By Tyler Reed
      Came here for help, If it’s in the wrong place I’ll move. I’ve got a 2000 model Polaris Magnum 500 that runs strong as can be for about 25 mins until warm, then sputters and loses power. Took it to a shop and they say it’s low compression and they will have to swap the entire engine. Seems a bit much and costs more than the entire bike. Was wondering if anyone has seen this and what the fix was. When I hear compression I think of gaskets, not an entire engine. Seems like if it was that bad it wouldn’t have power cold. I’m at a loss. Any help is appreciated greatly. 
    • By Billy Aldrich
      2001 Honda foreman 450s manual shift. i can shift through the gears when the ATV is off, but when I turn it on, I can shift into first, but I cannot shift to second or even back to neutral. Same with reverse. I can get it into reverse but cannot shift out. If i turn it off it will shift back fine, any idea? I just bought this and fear I got screwed over. 
  • Similar Tagged Content

    • By Ssg
      Hello! This is my first bike with a cvt it's a 19 Outlander 850 xmr. I use the 30" cryptid tires that come with the bike during hunting season since I hunt in a louisiana swamp and I have some 27" interco reptiles during the summer trail rides. So this past hunting season I got stuck and squealed the belt do i looking at cluch kits /adjustments to help with the low end but I dont want to mess with my summer riding so I'm looking for advice 
    • By Bruce Sawyer
      1987 YFM350FWTB 350 4x4 Big Bear when going uphill will sometimes act like the clutch realeases then re-engauge all at once.
      Seems to maybe be little more often if the engine is at about 1/2 throttle instead of at lower rpms.
      I have the Factory Service manual and checked the external clutch adjustment screw as ok and the H/L/reverse shifter lever linkage as adjusted correctly. It appears to be maybe a internal (inside the case) clutch issue or ??
      This is the type Big Bear that has the manual shift lever on the left front fender and has the manual foot shifter lever with 5 speeds forward.
      Can someone tell me how the primary and secondary clutch operates? 
      I assume one is mechanical and one is centrifugal. (what I'm asking is one clutch for the higher rpms and one for the lower rpms or ???. (the clutch appears to only momentarily release at the higher rpms is why I ask. The cycle has about 3000 miles of low speed through the brush hunting and has been well maintained, oil changed, etc and no deep water or mud useage.
      Anyone been into a similar issue with the big Bear ATV????
    • By mrfartsalot
      i have a 2001 suzuki quadmaster 500 4x4 that the primary cvt clutch is rusted on any ideas on how to get it off i want to try to reuse it if possible.
    • By Tyler Autry
      Recently started shifting hard from neutral to first causing it to stall. I'm able to lift up on the shifter and throttle up and slowly let off the shifter, like driving a standard. That is the only way to get it In gear and stay running. Also if I come to a stop and keep it in gear it wants to continue moving, eventually stalling out. I don't have much experience with the bottom end or clutches. I just now replaced friction and steel plates and that made no difference. Don't know what to do now.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...