Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ATVNetwork

Who’s ready for the Bako Sand Drags?

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By colin james
      View File 2017-2019 sportsman 450/570 with eps factory service manual
      This  is the factory service manual for the 2017-2019 factory service manual for the sportsman 450/570 with electronic power steering 
       
      Submitter colin james Submitted 09/06/2018 Category Polaris ATV  
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By marek porowski
      Hi, I got a check engine light and a diagnostic code 520194 2 and i know it has something to do with throttle voltage out of range
      I'd like to know if thats something that can be adjusted ? Or does anybody know what should i test  ?  I just bought this atv and I'm fixing it as its been in an accident. 
      I also changed throttle leaver as original one was broken and I noticed inside the 4x4 selector assembly there are 2 contacts but I'm not sure if they're suppose to make contact at idle. I found some info online but some are saying they're suppose to touch and some say they're not. I think id depends of the year of the machine but I'm not sure. I'd really appreciate any help that i can get with this
      Thanks 
    • By bradley nelson
      Im cool with the police in my area so i can ride on public roads.
    • By jrhoads23
      I picked up a 2017 Polaris Sportsman 850. The previous owner rarely rode it and it only had 53 miles on it (10 hours). I believe the Polaris break in period is something like 250 miles / 50 hours or something like that at which point they suggest doing the first oil and fluid change. My question is should I do it sooner than that? I believe this was manufactured in fall of 2016 so that means the fluids in there are 3 years old. Maybe that isnt a big deal and it is still fine to wait until 50 hours, but just wanted to check
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...