Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

nwr161282

1988 Kawasaki Bayou 220 Issues

Recommended Posts

Evening folks

I have a 1988 bayou 220 quad that has a damaged stator and been lying about for a few years. Recently I got the chance of a 1996 bayou 220 that had also been sitting for a few years so I decided I would try and make 1 good bike out of the 2. The 96 frame was rotten so I decided to use my original 88. I swapped the magneto and stator over from the 96 bike but then noticed that the magneto and stator wiring was slightly different so I decided best thing to do would be to change the wiring loom over. Having done this I ran into issues connecting my original run stop switch and push button start. The 96 loon had a connector with 6 wires where as the 88 had a 4 wire connector and a 3 wire connector. I sorted this by making up a conversion harness using the 2 looms but still the push button start would not work. I have now solved this by using some of the spare wires left beside the ignition key connectors and a relay. So now I have the engine turning over with the starter button. But sadly I have no spark.

On checking the Cdi unit I have found that I have 6 wires going into the cdi unit but all the wiring diagrams I've seen only show 5 for the 96 model. The extra wire I have is a grey wire which has a loose unattached end beside the ignition switch. Does anyone know where this grey wire needs to be attached. 

Thank you to anyone who has read this sorry it's so long but wanted to try and give the full story.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Jeff Wolf
      Bought a nonrunning 1996 bayou 400. Tore down engine and found major problems. Piston is damaged and cylinder liner needs replacing. Looks like cause was a broken oil pump gear.
       
      Question is can a piston from a prairie 400 be used? Is it the same engine? I assume the liner is replaceable?
       
       
    • By Arizona
      So a few weeks ago ended up buying a 02 Bayou 300 for 100.00
      Get there to see it and motor was gone through and parts missing, stuff not connected
      and a big freekin bucket of parts and bolts. He said had no power and mechanic said it was
      the wrist pin. Ended up leaving it in pieces and left like that. I end up getting most of it back together
      and manage to get it to fire up. I drive it and has no power! No missing just no power. I figure check 
      the timing chain as he did replace that. Well I spin the motor over and guess what!
      A blind guy could have done a better jobs. Just one question, I  loosen the top bolt on the tensioner then remove it
      right? Nothing is gonna fall inside the motor is it? just making sure, need this out before I can move the cam gear 
      to the right location. Thanks in advance Az
       
       



    • By mike costa
      Has any one tried using the Harbor Freight Winch mounting plate on a 2001 Kawasaki 300 4x4 Bayou? 
    • By Mudrecon
      Haven't got a service manual for this yet so I'm flying by the seat of my pants I made myself a shifter extension to go up by the gas tank took my foot shifter off to weld it and now when I put it back on I don't seem to be able to find neutral. Is there some asinine reason that you have to do something internally when you change or remove the foot shifter? It was a simple take off weld put back on and dog bite my pecker it's not working. I hope this is something simple I've done and that's something I need brain surgery for. Cheers fellas I know y'all will have the right answers
    • By JacobSlabach
      I have a gentleman that asked me to service his bayou for him.  I have always wondered what oil should be used in atv engines?  Pros?  Cons?  What weight should be used in what type of weather?  Is there one kind that I could bulk buy and safely used in any quad I worked on or owned?  What about performance?  Engine Life?  This has always been a 🤔🤔🤔 area for me with quads as far as why you would use one type of oil over another....
      Thanks!
  • Similar Tagged Content

    • By Kelby 746
      I have a 1987-89 (not sure on the year) Kawasaki bayou 300 that has electrical issues, I have replaced the entire harness with a proven good/used one, new CDI box, and two brand new coils, problem is that it tests no charge at the pickup coil, so I replaced and tested again with a so called good one that had been salvaged out of a blown up 220/250 (not sure which, the left side cover is smaller than my 300) in Missouri. It has a proven good OEM stator. I am trying to avoid buying a new start and pickup coil because it is so expensive so if anyone has a suggestion please let me know.
    • By Tubecatgs
      A friend of mine has this Bayou 220 that started running bad and parked it a few years ago. I foolishly volunteered to take a look at it. I noticed right away the choke plunger on the carb was broken and probably the reason it was running bad but now the old gas was evaporated and like turpentine. Before i even tried to start it, i drained/ thoroughly washed the tank out, new fuel filter, new fuel lines. Blew air through the petcock etc. Changed the oil and filter and air filter and new choke plunger and cable. I disassembled the carb and rebuilt it with a kit. I cleaned the main jet with solvent and poked a wire through it to make sure it is clean.. the engine now fires right up with the choke on and dies when i take the choke off. I adjusted the air/fuel screw to about 1.5 turns out and the idle screw about 2.5 turns out. The rubber boot between the carb and head does not have any cracks in it so I don't think it is leaking air. I originally had the clip on the needle on the second from the top ring... when i moved it all the way to the bottom it starts, runs and idles really fast and will idle eeally high with the choke off but if i adjust the throttle cable and/or idle screw to a slower idle it will sometimes stall but the idle will go up and down every few seconds and when you give it gas there is a hesitation... i tried moving the clip down to rhe second from bottom and same problem... i replaced all the parts in the pic to the top right. However, there appears to be a small o ring, washer and spring left over from the kit... i did not see these get removed..... a) any idea if where these extra parts go and if i need them and b) any other ideas on why i cant get it to idle right or carb adjustment ideas?
      Thanks
    • By Samuel Myers
      So, I've been having issues with my Bayou 220. It's gotten to the point where it was parked for 4 years just because of the issues.
      Issue 1, Grabby clutch: The clutch is adjusted incorrectly and grabs when shifting from neutral to 1st. It grabs before the engine has a chance to rev, which stalls it.
      Issue 2, Starter clutch blown out: The starter clutch is busted and spins free both directions.
      Issue 3, bad shocks: The springs or shocks are bad and the quad leans hard when getting on.
    • By wrench66
      Hi all,
      I recently acquired an old Bayou from a neighbor that I cleaned up a got running, then from nowhere a problem crops up where it refuses to start........ I pull the plug and it has no spark, pulled the plug cap off and laid the bare wire on the exhaust header and still nothing......once in a while though when I push the starter button but as I let off the button it might spark once. Now it did begin sparking normally just once and I plugged everything back in and it ran normally again until I turned the engine off. Next time I tried starting it we were back to no spark or the one spark deal.
      I have tested the stator wires at 140 ohm, the pick up at 130 ohm (I can't seem to find a reliable number for these values online), I bought a new ignition coil and ignition switch on chance those may have been the problem but were not, not sure where to look from here......... does the starter relay switch have anything to do with the ignition on these? I know these older Bayou's are magneto type ignitions and do not need battery power to operate but I wonder if there are safety switches involved I may not be aware of. Also, can someone point me to a good wiring schematic for the magneto 220's? Pre 95 I believe.
      thanks for any help!
      -- Ray
    • By Summer Warren
      Hey I just recently bought a 2002 Kawasaki Bayou 220 when you shift it jumps a lot and while it’s riding it it’s jumping as well but won’t stay started when you let off the gas Could somebody tell me what could possibly be the problem? Thank you
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...