Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Pvm85

1985 Suzuki LT250EF Quadrunner Valve & Rocker Arm Clearance

Recommended Posts

I have a 1985 Suzuki lt250ef quadrunner and does anyone know the proper valve to rocker arms clearance 

Share this post


Link to post
Share on other sites


Standard clearance for most engines is .004 thou being on the tighter side and .006 thou being on the looser side for most engines. So a clearance of not being able to slide .006 in, barely being able to slide .005 in and .004 is loose would probably be a good setting. The only reason for valve lash is to make sure the valves are seating fully and and some people saying cooling but not much. That is where I would set them.

 

If you want to be absolutely sure get a manual for your machine and it will say in there.

 

 

Sent from my XT1585 using Tapatalk

 

 

 

 

Share this post


Link to post
Share on other sites

Edited Topic Title and moved to Suzuki ATV Forum.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By jimsvtx
      I'm working on my brothers' 2002 Suzuki Vinson 500 . It sat for a few years before I got into it. I'm concentrating on the carb - I replaced orings, needle, etc. and soaked jets, bowl and anything that I could get off the carb that the solution wouldn't eat. I also removed the tank and flushed it with hot water - it's clean. The gas cap innards rusted away and the tank had a lot of rust and water in it before I cleaned it. I replaced the gas cap and installed a new fuel valve because the screens were broken in the old one. The bike will run but spits and sputters and backfires. If you "open it up" it falls on its face and stalls - but starts right up. Here is a link to an exploded view of the carb: Ohio Honda Yamaha Motorcycle ATV Dealer - J & J Motors - Kawasaki Suzuki Scooter Utility vehicle, parts, accessories, apparel
      Can anyone point me in the direction of the problem? It may still be a "clean carb parts issue" . My problem is that the parts list doesn't identify the parts to a degree that I understand. If you said" look at the pilot jet", I'm not sure which jet that would be....See what I mean? It'll run very good if I remove the air filter and cover the opening with my hand and part my fingers a little for the air to get in. Any help is greatly appreciated.
      Thanks in advance, Jim
    • By William Edwards
      Hello,
      I'm new to the site.  My son and I have decided to bring back our old quad from the dead.  Does anyone know where we can purchase a cylinder kit for it.  I think it's a 1986, but will have to check the VIN to be sure.
      The last time it ran, it was tapping and smoking pretty bad.
      Any help would be appreciated.
      Thanks!
    • By Wayne Starz
      I have a 2005 Suzuki Vinson 500cc automatic 4X4. I can only shift it in to park & High gear, it will not go in low or reverse, what's the issue & the fix?
    • By Stephanie Webb
      please help cant figure out how to bypass rev limiter in my suzuki quad master 500
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...