Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dave Ayoub
Ok i am not quick to jump on a forum and post a question without doing my own part and trying to research and solve the problem myself but I cannot find any definitive information anywhere about my problem. I have a Big Bear 350 that I picked up very cheap which had been sitting in a field for years. I am not new to building wheelers but this one has me beat. After rebuilding top end and replacing the carb it fires right up. The vin has some number worn off from being next to the shifter but from the parts in the clutch i assume it is early since 87 parts seem to be the only ones that match. Thats when the plot thickened.
Reverse works fine but when in the forward gears it would not go past 1st and was hard to get into neutral. ie. a it took a million clicks up to thump into 1 and as many down to find neutral. still never getting past 1st. within minutes i could hear metal screeching and whirling around in the clutch side of the motor. I took the cover off to find that 3 out of the 4 springs on the centrifugal clutch had broken and were shredded. Also the black mechanism that the pawl on shift shaft grabs moves was loose so it wasnt always grab to change the gear on the transmission. I tightened that mech, and replaced the springs assuming it would solve the problem since the gears were not actually changing from the lever and the carrier should obviously not only have 1 spring left.
After putting everything back together it did go into 1st fairly easy but then i again couldnt get it back to N without a million clicks down and couldnt get it to go past 1st. I did one time get it into a higher gear who knows what one but i gained some speed and dropped rpm.
If i jack both the front and the back wheels off the ground and run the motor it becomes much easier to shift and i can get it to run through the gears pretty well. Usually going into N without a huge fight. not perfect but it does hit neutral and roar while spinning the wheels instead of gain rpm and with the power.
I have tried every possible position on the clutch adjustment screw without any noticeable result. I think this could potentially be where my problem lies at this point.
does anyone know if the case is supposed to be threaded? because mine is not. obviously it seems as though it should be since every other bike ive touched has been. i even took the cover off my quadrunner to make sure it wasnt crazy.
when the screw is adjusted and the jam nut tightened the screw will just slide back out since there is no threading in the case. accomplishing nothing.
Does anyone have any insight on any of this? Are my plates stuck, Centrif clutch worn out, case stripped or something else crazy im over looking?
I got this 400, that wouldn't start. It would try, but wouldn't catch. I checked the valves and the L intake was tight at .002. The compression came in around 120. It didn't improve after a couple of drops of oil into the cylinder. So,I figured it was the valve causing the problem. So, I got the valves squared away, but it still won't start. I checked the spark and it seems like it's getting an intermittent spark. It fires a few times then nothing. If l let up on the button and then hit again immediately, it will fire a few more times, then repeat. So, what am I looking at as a possibility? Electrical issues are not my strong point. LOL
On Wednesday, September 18, our ATV was stolen from in front of our house after the locks were cut. This was around 2-3:15 AM.
We realize the likelihood of ever finding the four-wheeler again is slim to none, but we had to try and put the word out there. We have put countless hours in to restoring this Banshee. It was more than just a passion project, it also was our investment for a down payment for our future house. We are devastated and beyond heart-broken. If you see any suspicious postings on Facebook Marketplace, Letgo, Craigslist, etc., or have any other information, please contact us or the Prince William County PD.
*Update* We received a tip last night that it was possibly posted on Facebook Marketplace around 8AM yesterday morning with only pictures of the front and of the back of the ATV. The description only said: PM for more details. This came up in someone’s FB Marketplace feed that has it set for a 50 mile radius from Hartwood, VA. She also has her feed set to automatically translate everything into Spanish, so It could also possibly be posted in Spanish.
WHAT WAS STOLEN:
2004 Yamaha Banshee YFZ 350
White plastics with bright green and pink graphics/stickers
Prince William County, Triangle, Virginia
$500 REWARD FOR INFORMATION LEADING TO RECOVERY. BONUS FOR CONVICTION.
The post Stolen From Our Front Porch – 2004 Yamaha Banshee YFZ 350 appeared first on STOLEN 911.
View the full article
Hi guys I have a 2003 Arctic 250 4X4 it starts idles and runs great for about 10 min. then it spits and sputters and dies but it starts right up like nothing happened idles good till you give gas and it does it again let off the gas and it's idling great again this goes on for about 15 to 20 min. and then it takes off runs good all day like nothing was wrong.
I cleaned the carburetor it looked like a new one inside found a little gunk in one orifice, new air filter no crimped lines air line to tank good I did put a meter on the battery idling it said 16.5 V that's high I think would a voltage regulator cause this?
Suzuki shop wanted to sale me a stator for $556.00 but said it could be something else also thought I'd see what you guys say about it
Similar Tagged Content
The saga of the fan continues.
The Pin attempt in the fan shaft failed. I then moved on to trying to weld the fan hub to the fan shaft. I took it for a run the weld broke. Now it was truly F'ed. To recap the dealer price, they want $400 + CND for a replacement fan assembly.
I searched all sorts of after market places and no one carried one. Ebay had some used ones but they were $120 USD + Conversion rate for something as old as what I have. I went to Amazon and eventually settled on this.
What I found... and was amazed... was that the fan mounted to the Suzuki fan assembly bracket. I was prepared to manufacture my own mount conversions... It also came with "Harpoon mounts" (nylon zip tie like things that go straight through the rad. Anyways it mounted to the original bracket. It fit perfectly. Cut the electrical plug off replaced it with the Suzuki... all good. Let the quad heat up, thermo coupler kicked in the fan circuit, polarity was right... all was good.... Fan is under the circuit fuse rating.
so I finally have a solid fan solution. $34 CND vs $400+ CND
Fort Worth, TX- February 24, 2012 – QuadBoss is proud to introduce a new line of High Performance Radiator Cooling fans as well as OEM Replacement Cooling Fans. QuadBoss’ new High Performance Cooling Fan will make your quad run cooler and last longer. The increased air flow created by QuadBoss radiator cooling fans will help prevent overheating often caused by towing heavy loads or crawling through deep mud. The high-quality, sealed motor provides optimal protection from the elements and will easily mount to your radiator. The High Performance Radiator Cooling Fan meets or exceeds OEM specifications and comes with a 6 month manufacturer’s warranty. Endurance tested to insure a long life, these cooling fans provide the reliability you need to protect your quad.
Available on Amazon
To order QuadBoss products, contact your local authorized Tucker Rocky Dealer or visit QuadBoss’s website at www.QuadBoss.com to find an Authorized Dealer near you. You can also follow the latest news about QuadBoss on Facebook at www.facebook.com/quadboss. For product questions call 877-847-1558 or email at [email protected]
I have been working on a golf cart project for the last 4 months and ran into a major problem today, I have a 98 zr 500 snowmobile engine that I am planning to run in the reverse direction. I have set the timing to the opposite side of TDC and turned the pull starter around and come to find out, that I don't get any spark when pulling on the rope. I tested the wires going to the CDI and none of them get any power so I assumed that my stator wont work in reverse. Can I run power to the CDI from a battery and make it run? If so, what wire needs the power? If I can get it running, My next step is going to be to try and make it run on HHO and still inject the 2 cycle oil to keep it from overheating and ware out too quickly.
Has anyone ever found a way to turn a 2 stroke into a glo engine?
Im sure there is someone out there who is smart enough to tell me how to make this work.
Recently Browsing 0 members
No registered users viewing this page.