Quantcast
Jump to content


99’ Yamaha bear tracker 250cc engine problems


Recommended Posts

I have a1999 Yamaha bear tracker 250cc one day I started it with choke on and it idled for a min then clicked some and shut right off. I was using the pull start to start cause something wrong with starter but it won’t pull any at all now like it’s locked up  can someone tell me what the problem might be

Edited by Allen Junior
Link to comment
Share on other sites

Welcome to Quadcrazy. From your description it sounds like you heard a noise and then it shut off?  Is the bike in neutral ? It’s possable that the engine is seized up.  I would take the spark plug out and try to pull start it to see if the engine turns over.  Then drain the oil if there is any oil in the engine and see if any metal pieces are present.  It’s also possable that something else is locking up the engine causing it not to spin like a blown clutch bearing, maybe something came apart in the stator coil area or transmission. 

Link to comment
Share on other sites

  • 2 months later...

Yes I took out the spark plug and still won’t turn over I took apart the pull string housing assembly and was looking to see if something might have came apart in there but nothing      I can  turn back and forth about a quarter turn each way the part thats used by the pull string to start the engine but no more then that I also sprayed blaster down in motor where spark plug was just to see if maybe it would free up after sitting but didn’t work.    HELP PLEASE 

Link to comment
Share on other sites

Welcome back Allen. It honestly sounds like the engine has seized. I would take the head off exposing the piston and cylinder to see if there is any damage inside the cylinder walls. And maybe go further into this by taking the cylinder off completely. 

But prior to any of that make sure your not missing something else like the starter bearing or in the stator coil area   

Did you drain the oil? 

I have the same bike and it’s reliable and tough. But if there was no or low oil well that’s that! 

Hopfully you will find out and keep us posted. I’ve been a little busy since I opened up my own company but will try to check in from time to time. 

Goos luck. 

  • Like 1
Link to comment
Share on other sites

  • 10 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By John Sinclair
      I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY.  ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996.  WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE  CABLES THE NEW CARB ONLY HAD ONE CABLE.  HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE?  
    • By McG75
      1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler.  Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance. 
      .
       
       
    • By mehim
      Hi everyone. 
      Let me explain the thread title. 
      My husband and I are very active in the nudist community, and we have stayed at many and most of the mainstream nudist and clothing optional campgrounds in the USA. We are now approaching our retirement and would like to start a podcast to share those off the road / backwoods / little known camping areas where nudity is allowed. We have purchased a 5th wheel camping trailer with a rear garage for the ATV and now need some good reports on the one to buy. 
      We are most interested in a side by side unit but would love to get your thoughts. 
      Feel free to stop by and say Hi and ask anything you would like to better understand what we are looking for in an offroad unit. 
      Thanks for reading and hope to hear from you. 

    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
×
×
  • Create New...