Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Dean Base

Honda 350 Rancher 2000 Carb

Recommended Posts

I have a 2000 Honda 350 Rancher was working on carb and broke Valve Assy. off what is it's function?

Share this post


Link to post
Share on other sites


13 hours ago, Dean Base said:

I have a 2000 Honda 350 Rancher was working on carb and broke Valve Assy. off what is it's function?

Here's the diagram, did you break #28? 

This link is available to logged in members only. Please login or register to view this link.

image.png.a5355603055cf967715144eea620fb9d.png

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

    • Polaris ATV Valve Adjustment

      I've never done this before but after reading a few thread I decided to check my valves for the first time and to my surprise it was much easier than I thought. My bike is a 2005 Sp 500 HO. I first pulled the seat and the right side panel off, and that's it! It wasn't too bad to get at. Next I pulled the spark plug out and removed both the head cover ( 8-8mm bolts) [ATTACH]1021[/ATTACH] then the side cam cover (5-8mm bolts). [ATTACH]1023[/ATTACH] Also remove the plug in the recoil cover (14mm bolt) to see the timming marks. [ATTACH]1022[/ATTACH] Next I turned the engine over with the pull cord untill it was at TDC of the compression stroke. The best was to tell that your at TDC of the compression stroke is to rotate the engine until the timing marks are parallel to rocker cover gasket surface. The cam sprocket locating pin will be facing upward directly in line with the crankshaft to camshaft center line. Now fine adjust by looking into the timing hole in the recoil cover and line up the upside down "T" on the flywheel into the center of the hole. [ATTACH]1023[/ATTACH] Now using a feeler gauge, slide the .006" (.15mm)blade between the top of the valve and the bottom of the adjuster and adjust accordingly [ATTACH]1024[/ATTACH] [ATTACH]1025[/ATTACH] To adjust, Loosen the locknut (10mm) and check clearance with a feeler guage. Clearance should be .006" (.15mm) for both, intake and exhaust valves. Turn the adjuster with a stubby flat blade screwdriver untill the proper clearance is achieved then tighten the locknut (5.8-7.2 ft. lbs) while holding the adjuster in place with the screwdriver. Re-check the clearance with the feeler guage one last time and re-assemble the covers (72 in.lbs) and plugs. The only thing that i noticed was that I had to clean and silicone the side cam cover other than that I found the whole process rather simple. I'd give it a 4 out of 10 on the skill level scale. I hope this helps! Thanks Rich

      By PolarisRich, in Polaris ATV Forum

        
      • 7 replies
      • 23,342 views
    • Need used stock pipe for a Honda 400ex

      Anyone know a place i can find a used stock pipe for a 400ex?  I would love to find a take off

      By afa913, in Honda ATV Forum

        
      • 2 replies
      • 34 views
    • Honda 400ex rear carrier

      Am i better off to just replace the bearings or buy the whole carrier?

      By afa913, in Honda ATV Forum

        
      • 1 reply
      • 32 views
    • Honda 2013 420 reverse problem

      My 2013 Honda 420 occasionally won't go into reverse. I don't think it is in the transmission as it does not make a click or noise. I think it is in the lockout. Someone told me when I ride near the ocean the salt can get on something. Any ideas?

      By Keith Proudman, in Honda ATV Forum

        
      • 4 replies
      • 51 views
    • 1988-1994 Honda TRX300 TRX300FW Fourtrax Service Manual

      View File 1988-1994 Honda TRX300 TRX300FW Fourtrax Service Manual This is the service manual for the 1988-1994 Honda TRX300 and TRX300fw Submitter colin james Submitted 11/10/2018 Category Honda ATV  

      By colin james, in Honda ATV Forum

        
      • 0 replies
      • 30 views
  • Recently Browsing   0 members

    No registered users viewing this page.


×