Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

kennyg833

2008 Arctic Cat 500TRV Transmission noise

Recommended Posts

Looking for info on a transmission noise on my cat . Started yesterday when driving sounds like gravel grinding when driving . it fine at idle . checked to see if drive belt was coming apart it is fine . u joints are good as are wheel bearings . Has anyone had this issue before ????

Share this post


Link to post
Share on other sites


Well found the issue . Bearing on the inner side of final drive carrier was totally obliterated !

Have it tore down to the bottom case . Dealer going to split it for me and then will see how much internal 

damage has been done .

file-5.jpeg

  • Like 1
  • Sad 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Kawiherder
      It starts and runs Ok but after a while the temp gage lights up and the fan fails to start.  Any suggestions on where to start looking would be helpful.  Thanks
    • By technofarmer
      Hi there i was needing to ask a question. I may soon be getting a UTV of one sort or another and not sure what is good or better to avoid?  So far i hear great things about the Arctic Cat Prowler and Havoc, and many speak well of the Kawasaki Mule all but the 610?  
       
       So what are your thoughts and especially experiences?  What have you had and used in farm life and trail riding that has held up well or hasn't?        
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By technofarmer
      Well its finally happened, its time to replace the belt on my 2011 Polaris Sportsman 500 H.O.   Is there anything specific i need to know before getting into it? Is there one brand of belt i should get over another?   I'm still on my first Polaris and plan to keep it at least another 8 years.   
    • By Andrew Paul
      Hi to all im new to here so here gos quadzilla xlc 300cc  and in 3 gear i get no drive and a lot of nasty nises can ony one help thanks andy.ps also what other engine gos in with no mods to do as im not that good thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...